Had to defrost the freezer to melt off all the ice before servicing. Once that was done the icemaker replacement only took about 15-30 minutes to complete. The new icemaker came with many accessories and adaptors that were not needed and the instructions were based on replacing an older model and not really clear for my model. They mentioned not being able to use the new stripper but it was exactly the same as the old one so I left the new one in place. All in all it was easy and did the job.
Lift the shelf off. Remove the broken pin from the slot in the door. Remove the broken end cap from the shelf - slides out with relative ease by just prying up slightly the rolled edge of the shelf where it snaps in. Slide in the new end cap. Put the shelf back in place. Literally took about 3 minutes.
Water Leaking out of bottom of refrig first then out of vegetative bins underneath
Replaced defrost thermostat and defrost controller and also noticed that run capacitator for compressor almost oxidized in two and ordered and replaced and cleaned out drain tube and invertor (which was blocked by frozen peas and other food)or water to drain during defrost cycle and put everything back together and seems to work fine now....storing beer in outside refrig now
I replaced both the punp and water line. the website depicting the repair parts was the best i ever worked with. The parts were high quality delivered on time and easy to install. Total job cost $30 as opposed the cost of of a service man or a new refrig.
A few small ice cubes in an empty try on return from vacation
Look at various pertenant DYI articles and videos on the internet. Replaced water filter with bypass plug. Checked water flow to icemaker water solenoid. Ran icemaker diagnostic test which failed. Ordered replacement. On receipt of replacement, began replacement work. To wit: Pulled fiidge from wall and unplugged. (Not necessary to shut water off.) Removed small freezer basket. Unloaded main freezer basket, removed it then removed the freezer door. (A screw on each side bolts the door rail of the chassis slide to the freezer chassis slide.) Loosened screws on rear, top of partition between icemaker and small freezer basket. Pushed up on partition front and popped out U-bar supporting partition bottom being carefull not to bend it. Removed same. Removed screws from partition and set aside. Removed grilled "thingy" between rear of icemaker and partition. Now have access to icemaker screws. Loosened the screws, pushed up and out and carefully let it hang by it's connector. Fiddled with the connector locking tabs and finally got it loose. Compared old and new icemaker. Have to keep the old water funnel. The new wiring harness was stiff and the connector had a different orientation. Twisted both the wiring harness and connector to align connector while the icemaker hung by it's cable being careful not to let the icemaer slip and fall to the bottom. After much fiddling, got the connector inserted and locked. Set icemaker over the two screws, pulled it down and tightend the screws. Put the old funnel into the new unit being very careful to get it right the first time. Put grilled "thingy and the partition and U-bar back in, put door back on, put the ice cube bin back, freezer drawers bac and reloaded the frozen food, plugged fridge in. Done! Time to replace icemaker was about 20 minutes and another 2 hours to do the rest ofthe work. Still required only a nutdriver and phillips.
I broke the left side slide rail while trying to clean out refridgerator
I had one of my guy friends do it for me. It took him less than 10 minutes, and probably would have been quicker if he had a better screw driver. Mine is a cheap girly one that he could not get a good grip on.
Video is a great but still need to read the instuctions because there are parts you may need on the old ice maker. Saved myself a bit of money by not having to call a repairman. The process was very simple. I am glad I did it myself. Thank you Parts Select!
unplug refrigerator. Remove Ice bin then remove the cover off the ice maker,(slides off from bottom then lift off top) no reason to remove ice maker completely. Remove center gear screw and remove main gear from Ejector blade. remove (3) screws holding the front plate. The motor and switches are attached to this plate from behind, do not remove the nut from the from the stud that adjusts the travel for the motor. The Motor and switches will come upt with the plate and the shut off arm will come out of a hole in the top right. Its ok just be careful when you put it back to get it in the hole. remove the old cam and replace it wint the new one and reassemble. Its a bit tricky to get all of the microswitches over the new cam just carefully wiggle the plate and cam and don't push too hard. once everything is lined up it should go back together and you can replace the screws and main gear :)
My Son removed two screws, electric plug and two (2) compresion nuts. He had to bend the bracket to fit, then replace it, in reverse order except the filler tube on the new valve was of a "stabb-in" type. Job was a piece of cake and this small project, solved all our problems with the Ice maker.
1st - checked water supply - old valve in water line was closed with sediment. 2nd - replaced water line valve and reconnected copper tubing about 1 hour 3rd. removed single outlet valve and installed the new part - about 15 minutes
Everything went well and was very easy. Unfortunately, the ice maker still does not work. Still trying to understand what is wrong.
valve wouldn't allow enough water to fill ice maker.
Started with a visual inspection. Turned off water. Removed old valve. Bent bracket to facilitate installation. Installed. Hooked up. Tested. Works as advertised.....
