Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Dryer makes noise when "Start" is pushed, but stops when you let go.
Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!
It took a while to diagnose the problem. I finally figured out it was the door switch by pushing it with my finger with the dryer door open and starting the dryer. It would run like that, but the switch was not being pressed in enough by the door. I ordered the switch and I should have been able to replace in about 15 min. But the old switch broke while I was removing it and it fell back inside the unit. So I had to remove the top and the front panel to access the door switch. That's why it took so long. If that had not happened it would have been a much simpler repair.
Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)
Removing the top and then the front of the dryer went fairly easily after finding the screws. The drum came out with just a little coaxing, does not gets screwed in place. To me the trickiest maneuver was getting my hand under the drum to place the belt over motor pulley and around the tensioner pulley. You must look up an image of the belt routing. It took me forever to figure that out. If not for that, this in a half hr fix. Ps don't forget to unplug the dryer.
Replaced drum bearing part and white slides.The problem was that it was not the drum slide support. It appears to be the the drum rear bearing of whch I am now ordering. The bearing replacement is a little more difficult, but I have taken this on as a challenge
Horrible squeaking noise that my wife allowed to go on for tooo looooonng!!
I went to replace all four of the drum slides but in the process of doing this, found out that the whole of the top support had been rubbed away! I therefore ordered a replacement top support and replaced it per the instructions in the PartSelect webpage and from the youtube demonstration and completed the repair. I had a little trouble with getting the top support installed, but by jiggling it around and persistence I was able to complete the repair. The help I received on the webpage and video were invaluable! Thank you to PartSelect and to the other users for all your help!!
Opened the door and removed 2 screws from inside/top of door. Removed top and then removed 2 screws from back of front panel. Lifted drum slightly to remove front panel and attached new slides.
Followed the Part Select video instructions which made the repair really easy!! Thanks for a job well done! ALSO.. the drum wobble was not caused by worn slides and felt. There are three screws holding the drum axle flange. Two of them fell out leaving the drum to flop about as it rotated. So we scavenged some screws from elsewhere on the dryer and problem solved. Once again.. thanks to Part Select for great instructional videos and great customer service ordering parts.
