Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer started to thump and scrape
First and most important - safety. Either unplug the dryer or shut off the circuit breaker. Remove the two screws to the top cover. To locate these screws just open the door as they are located at the top of the door opening. Remove screws and lift up the top cover and carefully pull towards you. Place to the side away from the work area. This now will expose two screws within the side panels holding the front door and front housing. Remove the two screws, lift up and out to remove front housing assemble. Be careful when you remove as the wiring to the light fixture is included. Just remove cover and place side ways close to the dryer. Remove the bulb then remove the white plastic drum bearing (snaps out or in when replacing with a flat screwdriver). Prior to installing the new drum bearing install the four white slide strips on top of the drum bearing. Review the old parts for comparison. These actually act as the bushings between the drum bearing and the clothes drum. Please keep in mind the slides do not come with the drum bearing when ordering. You must order seperately. Once the new assemble is snapped into the metal front cover/door now you can re-assemble. While you have the drum exposed it's a good time to check the belt for wear. Sometimes a worn or ripped belt can be the same symptom of the thumpimg sound. For the assemble just reverse all the earlier steps. Plug cord back in or turn on the circuit breaker and run the dryer. You should be good to go for more years of service.
To get to the slides, needed to take off the front panel, the top and then can loosen the front of the dryer. Pull it out enough to get to the slides and replace them.
evidently the pulley spring on video was very very very weak
the pulley spring took so much pressure to hold it down it took 3 men and a boy to hold it and place it in position to to get the belt on. Also there is not enough room to get your arms and hands in without getting some small cuts.Ultimately I removed the screws in the back of the dryer and spread the side of the dryer out to gain proper access. It was an easy repair if the spring would not have been so strong.
First I replaced the timer, but dryer still did not start. took apart dryer, jumper out door and componet near motor to see what problem was and to be able to run dryer while opened up. Actually motor had seized up just enough to not allow motor to start rotating. Lubricated motor shaft and rotated motor for oil to work its way in. Tried starting again and motor started. Buttoned dryer back up and reconnected wires to appropriate places and started dryer again and again.Worked for 4 loads of laundry and still working for 3 loads on Wednesday. Working fine
I followed the step by step instructions provided by Video! Very informative, easy to understand and follow! If I can do it myself, anyone can! Thank you !
Originally I thought that the Start switch was the issue, and ordered one. After taking the machine apart and running some tests, the issue was clearly not this switch, but a different switch that cuts power when the belt tension is no longer being applied to the idler pulley spring. I fixed this by bypassing this switch, which in my opinion, is error prone and serves no purpose. The switch can be accessed by removing the control panel, then top cover, then front cover, then drum. The bogus switch is screwed to the bottom left, near the motor. The idler pulley spring rests against it. Just disconnect the switch wires, then clip, strip and crimp then together to bypass the switch, and voila! Now if the belt breaks or comes off the pulley, the motor will continue to run, but you wont hear the wet clothes flopping around, so that will be the indication that you have a belt problem. Hope that helps!
Take out the two screws holding the top on with the door open remove top and remove two small screws in top front corners. I replaced the 4 slides and the drum bearing without the new felt, do not do this it continued to squeek after it ran the first few times when i got the new felt a week later i installed it in ten minuites and the noise is gone. I think it cost around sixty dollars and my dryer is back in action. Make sure that you clean all of the lint out of the inside of your dryer I had alot of build up near the chute for the lint trap.
I read the repairs that others had posted and how they did it. It was really easy. My only complaint is that I didn't know that I needed the slides that attached to the bearing and couldn't find them on the repair list. My dryer had a spot for 4 of them and only 1 was left. Otherwise, being a female, I felt great to be able to fix it myself! Thanks! Let me also say, I only have one good working arm/hand.
