Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
lower rack was rusty
Took out the old one and put in the new one! Note the delivery time was great! The part was ordered one day and delivered the next! Thank You Ed Andrews
I shut off water and pulled dish washer out removed all water. Turned waasher upside down. Removed sump housing screws and unscrewed pc fitting ,replaced new parts. Make sure things are tight before turning on water.
I removed screws holding the rollers to the side of the dishwasher. I pried the end caps from the slide. I removed the broken part from the upper rack. I then replaced the broken rack roller, inserted into the slide and screwed the rollers which hold the slide into the sides of the dishwasher.
We ordered our motor and pump assembly. When it arrived we followed the instructions that came with it. We had no problem with the instructions. We found it to be really easy. I was very happy since this happened 4 days before Thanksgiving. Thanks for the easy instructions, my husband got my dishwasher repaired in plenty of time for our Thanksgiving family get together.
Once realized needed to open the wheel rail a little to remove wheel stop, it wasn't too difficult. Took about 20 minutes. Part came in a couple of days and was the correct part. Was disappointed that a similiar part, looked the same on the web site costing about $54.00 plus shipping, ended up costing about $100.00. Contacted customer service, said I needed to contact the factory. Seems like they should have researched the problem, Andy Duer
Timer - (easy): Turn off power for unit at breaker box. Open the front door and remove the screws holding the front cover. Locate timer. Unplug timer and remove screws holding timer in place. Reverse process to install new timer.
Drain solenoid - (a little harder): Turn off water to dishwasher under sink and disconnect from plumbing. Disconnect drain line. Remove any screws holding dishwasher in place and start pulling unit from it's cavity. It should come about half way out. At this time you can peer under the unit and see the drain solenoid.
If you don't know what you're doing (like me) I recommend the following. Remove the water line from the dishwasher (and possibly the drain line) It should now be easy to pull the unit all the way out and tip it on it's side, fully exposing the drain solenoid.
Note: The drain solenoid provided to me was encapsulated in a different bracket than the original one in my dishwasher unit. It was necessary to pry the solenoid out by bending the bracket and installing in the original bracket. Then squeeze back together in a vice with a few gentle love taps with a hammer to squeeze it all back together. It was still a little loose but the solenoid just goes up and down so no big deal.
There's a little metal clip holding the white plastic arm to the drain valve. Let's say this O represents the diameter of the metal rod it's hooked to. That clip is removed by a small screwdriver pushing the clip away from that rod, this way: 0 ==> It will make sense once you do it.
From there it's pretty easy to replace the solenoid unit and reverse the steps above to re-install the unit.
I turned off the water supply to the dishwasher. Then took off the front panels and disconnected the water. I then unscrewed the dishwasher from the countertop, pulled it out luckily there was plenty of play in the wire, and drain hose. I turned it on its side and had to remove a couple clamps to free th piece that I was replacing. Once I got to it, it just unscrewed. I put the new one on and everything back together. It was easy.
I removed the dishwasher, removed the front kick panel, layed the dishwasher on its back, loosened the clamps and removed the old motor and pump assy. Cleaned up the area where the unit was, Installed the new unit, tightened the clamps and it was done. Probably took around an hour because of my cleaning up the sealing areas.
There was a video on the page as the part. Done in a flash. The axle was a little hard to get into the wheel so I soaked it in a little hot water and it whet in like a charm.
With coin, to remove the end cap from the front inside of the rail, insert the edge of the coin into the side of the end cap and push the coin to the rear while rotating the end cap to the inside of the tray until it comes free. Don't force. Pepeat for other rail. Repeat to reinstall end caps. You can can now slide out the the tray. Use long nose pliers to remove old rollers and insert new roller(s) on same prong. Do all 4. Reinsert tray and end caps.
over time the upper rack axles broke so the rack would just come out of the rollers. I ordered the parts from here and had to youtube how to get the stops out so I didn't have to unscrew the metal guides out making an easy job into a hard one. all you have to do is with a flat head screw driver is slightly bend the plastic end part of the stop which is in the metal guide that stops the wheels from coming out of the guides. once you bend out the plastic end you then turn the stop to get it out of the metal guides. if you youtube it its very easy. just be easy when you bend the plastic piece because I can see it breaking. I didn't break mine so the job was very very easy and took all of about 5 to 10 minutes to complete the entire job. I love this site it had real life info to help out when you need to do a job and trouble shoot your appliance.
