Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
element actualy was broken somehow
first I removed the 2 screws, I then pulled the element out., accidently lost one of the wire in the insulation and had to take the back panel off which was 8 screws. Probably doubled my time. I received my part in 4 days thanks to good service and FedX It arrived the day before Thanksgiving. Just in time, Thank You All.
My wife detected the problem Wednesday evening before Thanksgiving. We've had the heating element break before, so we knew right away what the problem was. We ordered the part that night, and even though we weren't able to cook Tom for Thanksgiving, the part shipped on Friday and arrived the next Thursday.
First, I turned off the power to the stove at the circuit breaker.
Then, I removed the two screws that hold the element in place. They are on the top of the flange and partially concealed by the convection element that juts out.
I pulled out the heating element, disconnected the electrical leads, and installed the new one.
I attempted to put the screws back in, but they were a little tough to line up. I decided to leave them out, knowing that I will probably be doing this repair again in a couple of years.
Hopefully, next time it won't be the day before Thanksgiving.
Oven quit in the middle of cooking the Christmas turkey. Fortunately we have a smaller oven on the top which finished the job. (a few hours late, but after a few cocktails and more visiting, it really worked out fine!)
I was blown away by how easy it was to order and receive this replacement part. I went on the web on Christmas afternoon, Googled "Magic Chef" and found your website. Your ordering process could not be easier (including the on-line drawings and all). I selected the lowest cost shipping method "3-5 days." Wednesday evening, I got your e-mail with the tracker. Thursday afternoon the part arrived! Saturday, we opened the oven, took out the old unit, and put in the new. It worked fine! Thanks again!!
My husband removed the screws holding the damaged element and removed it before the new one arrived. When we received the replacement part, it took only about 10 minutes for him to repair the oven, inserting the new element.
Called repairman, he never called back for a week. Gave up and found your website, ordered the part. You said it would take 3-5 business days. You lied, it was there the next day. Taking old element out starts with shutting off the juice. Remove trays, pans, etc. Unscrew two screws, pull out elements ends, unclip from wires, reverse the process with new one. You need a light to do this.
the new elements were super easy to replace. the old ones just pulled out and the new ones easily pushed in. the top one was a little more difficult only because it had brackets that had to be slid of and then slid onto the new one.
The broiler drawer support broke while removing the drawer for cleaning. Order part through Part-Select, arrived within 4 days, replaced broken part same day.
Broken part was already removed, so I used the screw from the broken support and installed the new support. Very simple, easy, and painless.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires reverse the order to install the socet was easy but after i was done discovered that the base of the old bulb was stuck in the socet keeped it for future use
Removed unit from counter, removed 14 screws holding glass top to frame, removed ceramic element, swapped over mounting brackets to new element, checked wireing as per instruction sheet (direct replacement) connected wires, re-installed glass top to frame and placed back into counter. ops check good.
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Simple repair.Just make sure you measure the length of element from back wall to plug in,width,and width of holes in back of oven.Simple repair with correct measurements.Pluged it in replaced screws plugged power back to unit , worked like a charm....Thank You!!!
Removed back of stove (6 screws), puled clips loose. Two screws inside oven, pulled out old element. slid new one in, replaced screws, slid on clips replaced back panel. Don't forget to unplug the stove frist.