Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
broke the igniter in the oven before I even got the oven installed
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.
Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!
Thanks to previous posters, this seemed to be an igniter issue, and I found the idea of swapping the broiler igniter for the bottom one particularly good - I knew exactly what part was broken and how easy/hard the job would be prior to ordering. The part used snap in electric components, so the only work was in removing and re-installing the parts. Working in the oven was by FAR the most difficult part of the entire process.
Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.
Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.
Igniter was not getting hot enough to allow burner to come on.
took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,
Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith
Gas would come on, would not ignite. Oven not heating.
Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!
The oven igniter would glow red but gas did not come on to light the burner.
I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....
Checked igniter it glowed but never got hot enough to open gas valve. I switched igniter from broiler to oven and oven burner lit. Switched igniter back to broiler as wires were shorter than the oven igniter. Ordered part from number and picture comparison. It took about 20 minutes to get it installed and all stove parts back together.
Remove oven door, remove burner bar, replace ignitor, splice wires together because the old electrical connectors had melted together. Shipping was fast and extra wire, insulation and ceramic wire nuts were included.
The oven igniter came on but the gas valve never turned on.
1. remove oven door 2. remove racks and oven floor 3. remove oven burner 4. unhook igniter 5. install new igniter 6. tuck wiring back in as reinstalling burner 7. put in the insulation supplied in kit 8. install floor and racks. 9. install door. 10. test system 11. oven came on. SUCCESS
I took a pair of channel locks pulled the old one off pushed the new one on they look really nice and was glad they had the parts for such an old stove. thank you,now my hubby is glad so he doesn't have to buy a new stove.