Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door Seal on oven was old, hard and breaking apart.
It was very simple, pull off the old one, then I took some pliers and pulled out the fasteners. Took new gasket from bag and it just snapped into place.
First I unpuged the Range. Then I removed all racks and bottom tray of oven. The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I turned the oven on and it lit in about 10 seconds. Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE. p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule . THANKS A LOT !
It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison
Lifted the top up, only a few inches as the possibality of kinking the gas line was a issue. Took two screws out and replaced the unit, threaded the thermostat down through the oven. It was a breeze. I am 68 year old woman and did I myself. Most importantly, the process of getting the part was amazing, ordered it in the AM and received it the next day (no extra charge)and by miday the range was good as new. Great service!
Had to take off burners and lift off top. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and removed old element. Then I did all steps in reverse to install new thermostat.
Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.
Parts came very quickly from PartSelect. Good service.
Igniters were flaky on 2 burners and almost dead on 2
The part didn't come with installation instructions specific to any stove/oven so I went by a previous testimony on this website and pulled out the stove, and started to remove the side panel to get access. Well turns out I could have done the whole repair in place because on my Maytag the igniter source is accessible by removing the utility drawer and it's mounted on a small galvanized steel panel at the left side which hides the part directly. The existing spade connectors were the right size for me but I did have to crimp them tighter (which was perhaps part of the initial problem). After installation, the spark is much more powerful and all burners lit first couple "clicks".
Remove burnes and top oven glass, , identified cables for each burner. Unpluged cables, remove old ignition module, drill a hole to install new module. Place module in location. I had to figure out what cables were for the right burner as after placing in the same location as old ignition Module it turned out that they were not identical. I did have to cut old plugs to be able to install cables to new ignition module. If the new part came with and adapter to old cables, as old plugs have small connectors, the new one comes with larger plugs. That would have made it esier.
Even though the ceramic insulator looked new (white), it had become non-functional, replacement was simple, 2 phillips screws, reassemble and test. Now I will have to order the other 3.
Electronic spark ignition would not ignite intermittently.
The spark moule was accessed by removing the bottom storage draw and removing the 2 phillips screws that held the spark module bracket to the frame of the stove located on the rear right side of the draw opening. The new module did come with new spade connectors that reqires cutting the existing connectors off and splicing and crimping the new connectors to the wires for each of the four burners depending on the model stove. Also I had to use zip ties to secure the new module to the original mounting hardware since the replacement module is not a direct fit. Each of the four burners now instantaneoulsly ignite when turned on. I will buy from Partselect.com in the future. Thank you.
I thought that the initial problem based on the users manual may had been the thermostat. Removal of the old unit and installation of the new one was quite simple. The only time lag was cleaning some of the surrounding areas of the oven as worked progressed. As it turned out though, the problem wasn't the thermostat, but rather the igniter. But, that was a fairly easy job as well!
First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.