Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bad ignitor
This was very easy. Just remove the bottom of the oven by removing the two screw in the back. Then remove the baffle from under that and you of will see the ingniter. The one wire will reach the gas valve, just splce the other. 6 screws is all it takes. Turned it on worked perfectly.
Oven very slow in lighting, then when got to correct temp shut down but wouldn't relight
1- put in new thermostat 2- put in new gas valve 3- put in oven igniter ....3rd time a charm. Now I have all new oven parts! My husband installed and said it was pretty easy, have to take the oven door off and inside bottom out.
Removed 4 burner knobs. Unscrewed 6 phillips head screws on manifold.Pulled back manifold enough to remove switch. Removed the Two wires from switch and hooked them up to the new switch. Slid new switch on to shaft and in reverse order, reasembled manifold, screws and knobs.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I reattached the new piece. It was the easiest thing ever and i'm a woman!
First I removed the two screws that held the element in place.I then pulled the element out and cut the wires.I used wire nuts to put the new wirers on and put it back in place with the two screws.I tried it and it worked perfect.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires....install new element and woalla.........save thangsguivingday thanks to part select .com..........
originaldrawer guide was cruched out of useable shape
first thing was to remove the crushed guide with pliers and a twist it was out. to install the new one islipped one side into the slot and took pliers and applied pressure on the lower glide into the slot; it was done presto. works like new. thanks, Fred . it was so reasonable i got a spare.
First i removed the broiler door and then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and cut the two wires. I strip the ends ,connected the new unit with ceramic nuts that was provided an reconnected the unit. all was done in less than 30 min. EASY!!! plug the stove back in and WORKED PERFECTLY. note i receive the unit the same day it shipped....WOW
first i removed the bottom of the oven [inside the oven] ,the part was right there,i removed 2 screws and unpluged the wires,then i cut the wire ends off the old part and used the wirenuts that came with the new one to hook them to the new part,then put it back in place,put the screws back in put the bottom back in and was done
ignitor wears out, tenants use the stoves as heat sorce
Opened the oven, removed the bottom plate located the ignitor within arms reach, removed two screws and a snap out part. replaced with the new ignitor and put the stove bottom on and waala...DONE I have ordered all my parts from Parts Select and have never had a problem. Thank you. Jody in Montana
Removed broiler pan drawer,removed two screws on element unplugged wires,installed new one. ,Tried oven, works like it did when new. It couldn't have been easier,plus I saved a bunch of money thank you partselect mike m.
oven would not allow gas to flow for igniter to light
removed broiler front by depressing the indents on the door slides, removed two screws holding igniter cut wires on old igniter and spliced new igniter to existing wires with supplied wire nuts then reinstalled new igniter and tested have been using oven ever since
The repair was simple - I first needed to test the original igniter with a circuit tester. Once I determined that the part was bad, I simply removed it and replaced it with a new one from Partselect. It was a matter of simply unplugging a few wires and splicing the new igniter in with wirenuts. Fairly simple.
First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires nuts, (from last repair) installed new igniter. Not rocket science here.