Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Unplug fridge, tilt back against wall to provice clearance to install new assembly. Used self starting screws to install. Used cordless drill with nutdriver to install assembly. Time to complete job-5 minutes
Temperature in both freezer and fridge sections to warm!
Dear Part-select, I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work
Tom Houck Spokane, WA Houck Photo 509-723-3418 tomhouck1@comcast.net
I removed the compressor start relay and replaced it with the new part. Initially it did not work. When I checked my work, I had to tighten the connector on the new part. Once I made the correction, the freezer is freezing normally again.
loosened 2 screws with 1/4 inch nut driver, disconnected electric connection lifted old ice maker out, replaced it with new one hooked up electric plug tightened 2 screws
We love our ice here. I seem to replace the ice makers one to two times a year. Generally the ice cycle gets off for some reason and it starts making loud popping/clicking noises (gear grinding). Its easy to replace. Simply loosen two screws holding the unit to inside of freezer and disconnecting the wiring harness. Unit slide up and out. Replacement is super easy (5 mins or less). Bam! Ice!
This refrigerator is less than 2 years old. I have had to replace the ice maker 2 times now. Cheap ass parts! Only one ice maker you can order so just be prepared to replace it yearly!
Needed to replace ice maker which had been making clicking noises as ice got jammed and then stopped working altogether.
Followed the instructions that came with replacement ice maker...was very clear and easy to follow and only took 5 minutes. I also watched the video sent via email with my order confirmation which was very well done and easy to follow. The only information that would have helped would have been a note to wait over-night for the ice maker to make ice as I thought I did something wrong when it wasn't making ice right away....waited until morning and had lots of ice. If I knew how straight forward and easy this was, I would have done it a lot sooner.
Ordered ice maker, watch video of how to. It takes less than 5 min. Installes just like the video. Loosen 2 1/4" Screws, lift ice maker up, unplug old unit, Reverse. Just make sure water tube is lined up when you install new unit and wire is tucked up out of the way. Mine did not really start making ice till the next day.
removed ice maker storage holder and then remove two philip screws and unplugged four pin connector. removed ice maker and installed new one . very easy to do
After determining the ice maker was getting water but not harvesting the ice, I ordered a replacement Ice Maker. Installation was easy. One electrical connection and two screws. Following the video to make sure I did not miss any steps I had ice in just a few hours. Just in time for a July heat wave!
Unplug refrigerator , loosing two screws. Lift ice maker up to remove from position. Disconnect electrical connection. Reverse procedure to install new ice maker.
The instructions that came with the replacement icemaker were very complete, in particular concerning the small levelling bracket on the bottom of the icemaker, because the old bracket needed to be removed from the old icemaker and transferred to the new one. This part of the installation might not have been obvious, so I was glad to see it clearly outlined in the instructions. The old icemaker was removed by loosening two nuts and detaching the electrical connector, and the new one was installed in its place. Fairly simple, the whole job took about 45 minutes because I work slowly and carefully. A more confident person could probably have the new one installed in 15 minutes. Only drawback: about three to four weeks after installing the new icemaker it has begun making a loud clicking noise on occasions. It is a repetitive (5 second interval) clicking, and only happens for about a minute every few hours and then stops. I am concerned that it might be gears prematurely wearing out and slipping. I guess I'll know in a few weeks if this one stops making ice.********************************************* Update: after about 9 months the new icemaker quit working and will need to be replaced. I removed the front cover from the icemaker and could clearly see that the teeth of one of the plastic gears were worn out and no longer meshing with the opposite gear. The drive gear was just spinning in place and making no contact with the larger gear.
Over the past 6 months, I noticed we were getting less and less ice. Finally it just stopped all together.
I found that the fill solenoid for the ice maker was down to a drip when energized. I ordered from this site and replaced. now plenty of water, but the ice maker would just stall and jump teeth. The heater which heats the ice up to free it from the mold was defective. Ordered from this site, and now working great.this sitet has good pricing, and the help illustration is great, and explains the sequence of events. This made it easy to troubleshoot. This refrigerator has not give a problem in over 11 years. The problem is "the ice maker". I have replaced it 6 times.
