Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
There was a horrendous popping noise when I opened the refrigerator door.
First I cleaned out the side door then, removed the three screws on top of the door. Lifted the door off and set it carefully on a kitchen mat.
I had to use the pliers to remove the existing bearing hinge as it had disintegrated in the door. Once it was out the new hinge slid right into place and I reinstalled the door. I had help with the door. It’s much easier with two people to get proper alignment and to hold it in place while you reattach the screws.
I would have to say the hardest part of this repair was cleaning out the refrigerator.
Took off Door on Refr. and unscrewed Doorstop, removed doorstop with broken Bearing and replaced with new Parts. Took about 20 Minutes including reattaching Door. A 10 year old can do it.
Water Was Dripping From Base And I Had No Ice Being Made Or Water In The Door.
Removed the plastic water tubes cover with a nut driver. Disconnected water hoses. Dropped control box assembly with nut driver. Removed old filter base with phillips screwdriver. Assembly opposite.
Evaporator fan motor quit and would not circulate cold air from coils.
Remove shelves and rear panels to get to motor. Motor is held in place on shroud by simple strap. Remove fan blade, then un hook strap, remove and save rubber spacers on old motor to reuse to remount new motor. New motor Mew motor has wiring harness that is universal. Cut out the three wires that go to the new motor leaving long as possible, cut wires from old motor as long as possible, strip ends of all wires 1/2 inch, connect wires by color,slip into provided wire connectors and crimp. Pull on wires to insure connection. Tie wires together so they don't touch the coils. Plug in and check operation. If all is working unplug and replace all covers and shelves. Plug back in and it will take few hours to reach operating temperature. Video of side by side repair shows easy removal of panels and motor.
Support stude for both vegetable crispers broken off
Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.
None of this was obvious - an online tip from another member was invaluable.
Water was leaking from the valve/pump for the icemaker
Remove the screws that hold the old valve to the side of the refrigerator. Next, detach each plastic tube and attach that tube to the same place on the new valve, and repeat (there are many valves). Afterward, I realized that many of the plastic tubes had become brittle and had mineral deposits, so I bought additional tubing for ice makers and replaced each tube, one at a time.
It was very simple-it is just an insert glass shelf above the vegetable drawers. But, it was fairly easy to identify on your website and delivered in about two days.
I worked for GM as a Frigidaire Tech, before starting my own business. I have retired now. I took the three screws off the back of the bracket holding the motor. Disconected wire harness and pulled out the motor. Reverse to install. servantoftheking@hughes.net
The icemaker would not make ice because I removed the filter
I removed the filter bypass from the box. I opened the refrigerator door. I put the filter bypass in the space where the filter was located. I closed the refrigerator door. I opened the freezer door. I turned on the ice maker. It worked.
After a power outage my refrigerator went warm & the freezer was cool.
I unplugged the refrigerator and removed the back panel in the freezer. Here the coils were covered in a block of heavy frost. The coils needed to defrost, I allowed this to happen of the course of a few hours. Once this was done I used the wire cutters, cutting the two wires to the thermostat. Doing this I checked the continuity & got no reading. Having ordered the part at a more than reasonable price including 2 day delivery, I was ready to complete the repair. Stripping the thermostat wires connected the the freezer unit, I attached the two wires color to color to the new thermostat. Here I needed to insert both ends into the connector (butt end), crimping both sides. Making sure each end I'd secure. Do this for both sets of wires. Placing the new thermostat back on the the cooper coil (on the same one it was removed from), put the freezer back in place. Here I only screwed in two, in case I need to go back in. I plugged the refrigerator back in turn the settings back to default or factory. Allowed the refrigerator to come back up to temperature for 24-48 hours. I did these and I'm glad to say my 12 year refrigerator is working just like before.
