loud "clicking" noise - refrigerator door hinge bearing
Easy-Breezy - took pockets out of door, lifted door out of socket, took out broken bearing - some had to be pried out and pulled out with pliers. Once out, inserted the new bearing and put the door back on by lifting into the top hinge and then letting it down into the receiver at the bottom. It took longer to clean out and put back the door pockets than it did to make the repair. Wish I had done it sooner. I am 76 and female. Should have done this a couple of years ago. Didn't know the problem until I found a part of a hinge on the floor beside the refrigerator. Then it dawned on me what might be wrong so I went online and found that "clicking" was a common problem and what to do - ordered the replacement hinge bearing and made the fix.
The frame for the meat pan in my Frigidaire refrigerator broke in the middle front, which made opening the drawer a little tricky.
No big deal. I took out the glass in the frame, took out the meat drawer, and removed the broken frame, which doesn't take any tools. After removing the frame, I inserted the new frame, which pops in to two clips in the back, and two in the front on each side. I cleaned the glass and put it into the frame. I re-inserted the drawer into the frame. And VOILA!
Ice maker non functioning, Ice maker not sending signal for w
Remove the old ice maker by loosening the screws and disconnect wire harness , next fit new ice maker in place connect wire harness and place new ice maker in place put screws in and tighten.
The repair was not difficult because you just remove the old part and plug it in and connect two wires. But I wish there was a way to test if the compressor is working before I purchased the parts. The compressor would not start so I was not able to repair the refrigerator.
Refrigerator was in storage over the winter and the housing froze and broke.
I removed the screws holding the shield covering the filter housing and cup. Unscrewed the cup, removed the filter. Then removed the pressure fittings holding the water lines on the housing. Then I removed the housing. Reversed the process with the new housing.
Old valve comes out with 2 screws, water lines removed and reinstalled on new valve just as they came off the old valve. Entire job took less than 10 minutes. Very easy replacement.
water leaking inside of refrigerator from filter area
I just removed the filter and then removed the filter housing. The housing is mounted using two screws. The only difficult part was removing the elbows from the water in and out lines. I don't believe the elbows are reusable. So I would go ahead and order new elbows when replacing this part.
Icemaker was producing hollow ice due to water was free flowing out the water dispenser during fill time for icemaker.
Removed old water valve w/ screwdriver, cut threads off old hose (as they just plug straight into new valve) & pushed hoses into new water valve. Solved both problems!!!!
Defrost terminator (Thermostat) Was Stuck Open, Not Allowing Defrost, Heat Gun or Hair Dryer
PURCHASE: Buy the terminator from the site because they sell the terminator (thermostat) separately. Other places have it with the wiring harness for more money. Changing it with the harness attached is a very, very involved project. It includes removing the entire inner liner of the freezer. The one the site sells requires only a simple crimp splice and shrink tube.
TEST- If you have another freezer, ice or a friend's freezer available, it is highly recommended that the new part be tested: You will need an Ohm meter or a continuity tester. You can make one very easily per instructions found on line. TEST RESULTS- a) At room temperature. An Ohm meter should show "Open". b) After being in a freezer or submerged in ice water for at least an hour, the Ohm meter should show "Closed".
I have installed hundreds of defrost thermostats. Very occasionally one is defective. This project is a bit involved, so it is wise to pre-test.
HOW TO INSTALL THE DEFROST TERMINATOR (THERMOSTAT): A) Prep Remove Food & Be sure the freezer is warm. Parts need to be pried upon & cold plastic breaks easily. Tip: Put the screws in separate cups with labels. This will make re-installing the many components easier. Gather tools from the attached list.
B) Unplug Unit (Turning it off is not sufficient protection against shock.)
C) Remove Light Bulb (If it gets broken while working, glass may get in the eyes.)
D) Remove Drawers (This is a bottom freezer unit with 2 drawers) 1) ) Upper Drawer: a) Locate the 2 rectangular boxes covering the gears. They are on each side, toward the rear of the drawer. b) With a nylon spudger, push in the 2 clips on each box and lift the boxes 1/4". They will stop at 1/4". c) At the front of each track, remove 2 hex head screws with a 5/15" nut driver or a 1/4" flat bladed screwdriver. d) Lift the front of the drawer a small amount while pulling drawer. Lifting allows the 2 stops on the drawer to clear the track tabs. e) When near the end of the drawer, lift the gear wheels slightly to clear the track. f) Put the drawer out of the way.
2) Lower Drawer With Front Door *Leaving the door attached makes it easier to align the drawer when reinstalling it later. It must be straight or the gasket will gap. a) Put a thick towel on the floor, in front of the unit, so the door can be laid upon in without scratching the handle or the floor. b) Pull the drawer out and look at each track about 2/3 of the way to the back of the freezer. You will see two long, white tabs. c) Push a tab in while pulling the track slightly forward. Firm pulling is required. Repeat on the other side. d) Drag the towel and door out of the way
D) Remove the air grill at the top, rear of the freezer. 1) There is a clip in the center to push with a spudger. It is easy to see in a photo of a replacement fan bracket. 2) On the right side, in the top row of square holes, is another clip to press with a spudger while pulling that side of the grill out. 3) On the left, there is an air chute blocking the clip. It can not be removed. With the right side pulled free, gently wiggle & pull the left side until the clip clears & the grill is free to leave.
E) Remove the Ice Maker (Water does not have to be turned off) 1) Loosen, but do not remove, 2 screws above the ice mold. 2) Remove the one lower screw & put it aside. 3) Lift the ice maker & store it out of the way. 4) Do Not turn any wheels by hand, nor bend the bail wire.
F) Remove the Thermistor Cover (Upper Right Back Wall) 1) Gently squeeze the sides while pulling. Stop as soon as it's free. 2) Note how the thermistor & wires are installed in the cover & thread the thermistor free. 3) Set the cover aside.
G) Remove The back Wall 1) Remove all visible hex head screws. 2) The back wall can now be removed. 3) Set it aside where it will not scratch any surfaces, as the edges are a little sharp
H) De-Ice the evaporator with a heat gun or hair dryer. Don't hold the heat source in one spot for long or wire insulation or plastic components will be damaged.
I) Note the permanent ice ball in the upper-right corner. The defrost thermostat is under this ball. Melt it with heat.
J) Install The New Thermostat Hint- Take the thermostat to a hardware store to buy the correct size shrink tube and crimp sleeves (butt connectors)
Incorrectly! There are two sizes of door bins and they are not interchangeable. I ordered the wrong one, only to discover that door bin was also cracked. I now have two new door bins. All's well that ends well...they are really easy to instal, but if not the correct one, it will fall off!
the closer plate was cracked and caused the door to catch and make a popping sound.
the repair was so easy to do. it did take 2 of us to handle the door removal and reinstallation. we watched the video and carefully removed the door and had no trouble at all with the new parts installation. we knew what to expect and successfully fixed the frig! Good Deal!! Easy fix!!
