Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
the door would not close on it's own
The parts came within 2 days. The delivery was great. I took the food off the door, then removed the top hinge. Lifted door off bottom hinge and laid the door on a blanket on the floor. I then had access to the closing mechanism top and bottom that is just two plastic cams that lift the door as it opens. The weight of the door then is used on the cams to help close the door with the appliance level. It was very simple and assembly was just reverse order.
Water coming out of the ice maker when dispensing water from the door.
This issue was noted in the advice area as being a filter, or valve assembly. But it turned out to be a diode kit that was causing this issue. I don't know why I could not find this issue anywhere on line? When I received the diode kit there was instructions that noted exactly the problem I was having. The fix was easy just a few wires cut and spliced and viola fixed.
Removed 4 screws holding face plate onto ice bucket. Removed the 3 screws holding the ice crusher housing. Noted postion and rotation of teh s;ring loaded ice selecting rod. Removed broken crusher housing. Reveresed process for installion. Took for test drive. Operational...
This could not have been easier. I came to this website looking to see how much the part was before i called a repairman to come do it. I saw everyones instructions and decided to try it myself. To replace the ice maker you basically unscrew 2 screws, unplug the broken one and remove it. Plug in the new and tighten the screws to hold it in place. I would have been REALLY unhappy if i had called a repairman and saw that was how it was done. Could not have been easier
The repair was easy. The problem was the lack of explanation. This may help other customers. I was told by the virtual trouble shooting system that about 30% of the cure was to replace the water filter and 70% was to replace the water valve. I did both and still had the problem. People need to be told why they have to replace the water valve. The reason is this. The valve has a very small leak in it that lets water continue to flow into the freezer compartment drop by drop. Eventually, this freezes and clogs the hole , so no water can pass and thus no ice can be made.In either your web site or another they stated that it may freeze up here, but there was no connection to the water valve.It seemed like it was another topic. Its very hard to see the frozen area, unless you remove it from the freezer area. I wish I was TOLD TO DO THIS, after i replaced the valve It would have saved me a repair bill. I hope this helps others. Take care-Bill
The radiator was not being properly defrosted and the refrigerator and freezer could not keep the temperature. Two things can be causing this, the defrost module which defrost the refrigerator on a regular basis ($110) or the thermostat ($18). I tried the thermostat since it is very easy to do (remove cover plate inside the freezer, cut wires of old thermostat, connect new thermostat by stripping wires. Presto...however the thermostat was NOT the problem. The problem was a blown timer circuit board that controls the regular defrosting. That repair was done by a technician. The board was $110, it seats inside the refrigerator in the control panel area.
Unplug turn water off Removed two screws with nut driver loosen one Disconnected three solenoid valves Disconnected four water lines Plug tubing in, tighten one flare fitting Reattach wires to solenoids Slide under loose screw, replace two screws Turn water on check for leaks plug in get a drink of water
Housing that the water filter was cracked. I think ,setting was too cold and froze and cracked it.
It takes a 1/4 " nutdriver to take one screw out that holds the cover over the water filter. You have to come up from the botton of cover. Then take two water lines off housing , by pushing the round collar back toward the fitting,and pull fitting off housing. Then take the two screw out that hold the housing on. Make sure you have the water turned off before you start.
When the ice maker is over filling, either the valve is defective or clogged, or the ice maker is at fault signaling the valve to stay open too long. My problem was the latter. I had already replaced the valve, thinking that being only 2 years old, how could the ice maker be faulty. I was wrong. Ice maker unplugs and comes out with 2 screws. A quick swap with the new ice maker and all is well. Simple
The door has nylon gear teeth that wore out and needed replaced. The ice chute came off very easy with 6 screws. I used a punch and pliers to remove the hinge pin. Then the door came off and the new one put on. Very easy. The part was ordered on Sunday and arrived on Tuesday.
Unpluged the item. Turned off the water source. Removed the card board cover. Dis-connected the water hoses. Unpluged the connetors. Matched up the colores and put it back together, very easy. Everythings was color coded.
I shut off the water supply and removed the 4 screws from the cardboard back revealing the water valve. I removed the 2 screws which attach the valve to the refrigerator and removed the water valve. Once out it was a snap to unplug the electrical leads and unscrewed the water lines, Insalling the new part was a matter of reversing the above procedure. Everything is color coded which made this replacement extrememly simple.
I will definitely use you guys in the future. The ordering process was great and delivery time was ultra quick! Thanks for an easy part replacement and simple install.
most importantly on the page with the necessary part..cripser support for the refrigerator--- there was a brief insructional video on how to properly dislodge the broken part and replace it with the new showing the simple tools needed. I am not handy at all but it took me all of two minutes thanks to the helpful video.