25331438100 Kenmore Refrigerator - Instructions

Simply clipped it on.

none

I installed new end caps brackets with bars by putting them in place. Now the refrigerator looks new again. These parts were installed in the door, which was broken/missing. This prevented a person from being able to store anything in the refrigerstor door until it was fixed.

These were easy pop in pieces so no tools were needed. Very easy and quick. What I liked best about PartSelect.com was the pictures and labeling used in order to select the correct part. That was my biggest concern. It only took me about 15 minutes to find and buy the parts I needed.

Received 3 parts. Snapped them together. Attached them to fridge door.

it was great. I ordered the capacitor for my frigidaire frig and it arrived
in 3 days. plugged in the part to the compressor and my frig has been
working ever since. I spent 3 minutes ordering the part and 30 seconds
attaching it to the frig. Easy, very easy. saved myself a 75 dollar repair
visit. thanks

simple job

Basically we put the end caps in place and then inserted the retainer bar into one of the end caps and measured the length needed to make it fit the other end cap. The three shelves in the refrigerator door were the same length. So we measured each one, cut to the correct length and then installed each one. The freezer retainer bar was shorter but we followed the same procedure used for the refrigerator door. It took less than 30 minutes to do all five shelves. It was very simple and easy to install.

When my side by side Kenmore refrigerator quit keeping the top half of my freezer and refrigerator cold I called Sears to see how much it would cost to get it checked out and fixed. Bottom line it was going to cost minimum $65 (which was just for him to come out) to $250 on up depending on what the problem was. So i decided to "do it myself"! I took it apart and within a few minutes figured out that it was my evaporator fan. So I went to sears to order the part based on the part number and with shipping and handling it was going to cost $125. While at sears I got on one of their computers and quickly looked up Kenmore parts and partselect.com came up and I quickly found the part for $62 and I chose overnight delivery and spent a total of like $83. When my part arrived I realized that the wiring/plug ins didn't quite match up. So I got online and went to their website and found a video for "do it yourself'ers" like me on how to splice the wiring to make it match. It took me about 20 min to splice the wire and put my refrigerator back together and IT WORKED! Easy easy easy and I saved moocho bucks! Ill never pay a repairman again. Oh and by the way, I am blond! :-)

Snapped the broken end caps off the rail; snapped on the new ones; snapped the assembled rail/end caps into the door. It was a snap.

thanks to all of the people who had the same problems I was able to make a quick fix on my fridge. I pulled the back cover off and found the compressor not kicking on so I replaced the start cap. and im back in bussiness.

Thrilled to realize I didn't have to replace the entire bracket ($$) but was able to buy this inexpensive end cap, remove the cracked one and snap this new one in place. Inexpensive, fast and easy as pie. No tools needed. Good as new.

I was thrilled to find out I could order the parts so inexpensively and easily from Part Select! The shipping was FAST! No tools required, just snapped in and done!

The website said 60% of people with same refrigerator problem solved the problem with a new fan kit. I received the fan kit within 3 days of ordering. Was shipped from Fresno, CA to Long Beach, WA. The fan kit was to be installed behind rear panel in the freezer compartment. When I removed the old fan motor, I noticed the shaft turned harder than the new fan motor, suggesting a problem with the old fan motor. I plugged in the obvious fan motor power bundle with no problem. The instructions and diagram with the kit nearly steered me wrong. Instructions, diagram and splices with the kit instructed to cut the "extra" wire bundle and splice "similar" wires (should have said same color wires). Luckily, I ignored those instructions when I remembered the U-Tube video depicted the extra wire bundle was to be inserted into a factory penetration in the back panel, facing the freezer compartment. This power bundle is for adding an ice maker, which my refrigerator did not have. When reassembled and the refrigerator restarted, I could immediately feel forced air in the refrig, where there was no flow before fixing. I observed that all the refrig and freezer dials do is act like a valve to increase or decrease air flow to the compartments. The dials have no mechanical or electrical connections, just designed to divert air flow from across the cold 'evaporator' fins. I recommend other consumers to remember carefully what they see in the video and watch again if stumped during the job. The video was better than the instructions which may have been written in China or India. I am happy. Repair was a lot cheaper than a new refrigerator and I would not have bought another Frigidaire. Thanks to this website. r. andersen

My husband watched the video on your website and found it very easy to do the repair. The repair company that diagnosed the problem wanted $210 to do it. The part I ordered was under $20, and after he installed it the refrigerator has been working great. We would highly recommend your site to anyone who needs to fix anything!