Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Switch - and the connection wire to the burner
First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.
Burner only worked on High and very low temperature setting.
Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.
Repair job was easy but longer than the 15 minutes that it said it would take.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I replaced it with the new element that took only two days to arrive and that was without paying extra express shipping fees. It couldn't have been easier. I didn't even wait for my husband to come home and install it. I had an oven-baked meal ready when he got home. I was very satisfied.
I had begged my husband for 1 1/2 years to fix the oven and he said it would be cheaper to buy a new one but he wouldn't go buy one. So I decided to fix it myself. I removed the screws that hold the element and then I pulled the element out and disconnected the wires. I then hooked the wires to the new element and pushed it back in place and attached the two screws. I made sure to put the insulation back in place and now I can cook cornbread again! Thank you so much for making this so easy for me to do by myself.
My daughter and I turned off the breaker to the range and removed the old element and replaced it with the new one. My husband came home and took over after we had done almost everything ourselves!!
Unplugged oven. Removed the two screws from inside the oven that secured element to the back. I then removed the protective cover for the plug from behind the oven-three screws. Disconnected the element from the electrical wires, removed and replaced the element. And reassembled the cover and all the screws in reverse order. Plugged it in. Presto, 5 mins and works great.
The bake element is very easy to replace. Turn off the circuit breaker to the stove. Two screws (1/4" socket needed, not screwdriver) come out to release the plate, then two more screws of the same size to unfasten the element to the stove wiring. Reverse the process to put the new one back in. I let my fourteen year old son do the whole thing. By the way, the photo of the element on the web site did not look like the element in my stove. I called customer support and was assured that it was the proper part. When it arrived, it did exactly match my element. The photo on the web site was incorrect. (Part number PS249466)
Unpluged Stove, Unscrewed the wires attached to the Element in the back of stove after I removed the cover. Removed the two screws that held the Element at the back of the oven compartment. Then replaced the Element with the new one and put back the screws, the wires and the cover in the same sequence iI took it apart. Plugged it back in works like new!
.....then tested for voltage, had it. Ordered the element through partselect.com and it came in the mail THE NEXT DAY! No kidding! Installed it and the wife is back to her good cooking. All is well, thanks partselect.com. John R., Pompano Beach, Florida
My husband removed the screws holding the element, disconnected the wires from the old element. He then reattached the wires to the new element, putting it back into place, tightened the screws, and we were cooking again. The shipping service was GREAT! I ordered the part on-line and it arrived next day! Thanks!
I removed the original element with socket set (two hex nuts). I removed the element and face plate, reversing the steps when installing the new element. It was simple.
the existing element would not heat up, it was broken
turned off the electric at the breaker box. removed the door, and racks. unscrewed two bolts, pulled out and unscrewed the leads. reattached the leads, and pushed in and reattached the element. put the racks and door back on. turned on the electric and then tested the oven. easy!!
This job was easy. I removed two screws to release the element from the back of the oven, two more screws to release the electrical connection, connected the new element with the new screws provided and reattaced the heating element to the back of the over. It took two tries to get the element so that is sat level at the bottom of the oven. Ten minutes later, I was making dinner!
I noticed two screws held the heating element in place. I removed the screws. Pulled the heating element out a few inches. Removed the two additional screws which held the two wires on.
To install the new element, I used the two new screws that came with the element to attach the wires to the element. Insert the element into position and attached the element to the rear wall with the two screws which were first removed.
