Motor was working and rotating lower portion of agitator, but the top was not spinning.
1. Remove the fabric softener receptacle
2. Remove the plastic dome shaped separator with a rubber o-ring around it (directly beneath fabris softener receptacle)
3. There is an 11mm bolt right in the center. Use socket wrench to remove bolt.
4. Remove agitator from washign machine.
5. Separate top half of agitator from bottom half (this was the most difficult part for me; unlike others who have described this repair, mine would not simply pull apart; I spent quite a while trying to pry up the white plastic clips extending from the bottom piece through the clear plastic piece that covers the "dog teeth" that make the top piece agitate)
6. Once apart, replace worn "dog teeth" with new dog teeth.
In the spin cycle, drum would'nt spin unless assisted
First off unplug the machine then turned off H/C water supply and removed hoses, laid the machine on its side, removed 3 motor supp. bolts, loosened drum pulled out shaft and clutch assembly was right there. Also replaced coupling while it was apart. And to think, a svce company wanted 179.00 just to walk in my door and diagnose the pblm. Then, parts and labor were extra. Thanks for the help/advice, piece of cake!!!!!!!
Removed top cap on agitator w/ flathead screwdriver. Removed protective cap over bolt and cog housing shaft. Used 7/16 deep socket w/ extension to remove bolt. Removed housing where stripped cogs were located. Cogs seated loosely in shaft housing no tools required to remove cogs. Replaced cogs in housing, made sure everything was lined correctly. re-inserted housing into shaft. ,screwed bolt, replaced caps and works like new.
valves allowed water to overflow during the rinse cycle, sometimes took forever to fill.
I removed the screws holding the control unit down, removed a couple at the rear, Disconnected the electrical clip that plugs into the top, under the control unit. This allows enough slack to pivot it ( the control unit) upside down and get it out of the way enough to remove the spring clips that hold the top to the back. Popped out the two clips that hold the back to the top. Pulled the back out, up until the plastic soap dispenser , (which is attached to the back) hits under the lip of the top. This does not allow enough room to get to the valves. I finally figured out you have to lift the entire top up high enough to clear the back while pulling it ( the back) out. Disconnected the hose clamp, electric connectors, installed the new valves into the supplied mounting plate replaced the valves . Re -connected the hose and electric connectors and re assembled the back. The only problem I had was when one of the spring retainers that hold the back to the top popped off and fell inside the unit, which forced me to remove everything including the back bottom screws, which caused the sides to pop off, the mounting ears , which are attached to the back, Took some finesse but finally retrieved the spring clamp and finished everything back together. It was a bit tricky keeping the plastic gaskets between the back and the sides from falling inside as I reassembled it. But all is well, and would have been more difficult without the expierence written by others who posted, on the site. Thank you to all, for the help. I hope my efforts will help someone else.
Pulled the big front panel by removing two screws near bottom of front and pulling out at bottom until the top pops loose. Vacuumed out all of the dust and checked for loose connections. Ran dryer - igniter would light, but no gas. Checked the two solenoids with a VOM. the one with the two leads would intermittently read Infinity (open). Super simple repair. Remove two screws on solenoid bracket on top of the gas valve, Replace solenoid and plug it back in with the easy push-on connector. NO PROBLEM - all fixed.
In the middle of changing loads there was snapping and sound and drum stopped turning.
I was hopeful it was the belt. But, I had no idea how to get to it. I used the model no. and looked on line for pats and schematics. That gave me a sense of what to do. I started at the rear and removed the back panel. It was like peeling an onion because then, I wasn't sure what to remove next. So I just kept removing nut head screws until eventually I had loosened the sides, removed the top and discovered the front lifted up and off (no screwed attachment.) There's grounding wire that must be detached. Don't forget to re-attach. Without proper grounding you could be electocuted! I was careful to remember how it was attached. To get to the pulley, which is on the front, I had to remove the drum. I found the snapped belt. The pulley is held in place by tension from the belt so, once the belt goes the pulley detaches. I tried to find the belt locally the following week but was unsuccessful. I found the part on-line and had it in four days. It was tricky getting the belt and pulley in place. I persevered. The parts ( I replaced the fliter that needed replacement for years too) came with installation instructions. Its possible I did not have to disassemble as much as I did. Oh well! Although I'm fairly mechanical, I'm still pretty proud to have been able to do it and save the cost of a repairman.
Slipping Spin clutch due to leaking gear-case seal.
1. Unplug the machine. 2. Turn the water off. 3. Disconnect the supply and discharge hoses. 4. Open the cover and remove the cap/cover of the agitator. Use socket wrench to remove the bolt securing the agitator. Pull up on the agitator and remove it. 5. Lay washing machine down on it's front. Remove the inlet and outlet drain hoses from the discharge pump. 6. Remove the 2 "faston" connectors from the motor start capacitor (looks like a D cell flashlight battery). Rock the connectors back and forth and pull gently until they come off. Polarity doesn't matter but to be safe make note of the positions. 7. Press the release clip on the motor connector and pull to disconnect it. Move the wiring harness out of harms way. 8. Remove the 3 bolt securing the motor and transmission assembly to the bottom of the tub. Pull the drive assembly out of the machine and place it on a suitable work surface. 9. Examine the tub brake assembly (still on the bottom of the tub), the clutch assembly (on the motor/transmission assembly you just removed and everything else for wear or damage. Now if you decide to proceed with repair continue with the following steps. If not you're done. 10. Remove the inverted cup washer from the agitator shaft of the assembly. Remove the "U" clip from the shaft and remove the clutch mechanism from the drive assembly. Make a sketch of the position of each of the removed components to aid in reassembly. 11. Now you can see the gear case cover and it's seal. If it is leaking (as mine was) you will need to replace it. 12. With the assembly level remove the bolts around the cover and remove the cover. Place the cover on a flat surface and with a screwdriver or punch drive the old seal out of the cover from the outside in. 13. Clean the seal area and check for damage. Clean the cover and transmission housing surfaces of old gasket material. There is a factory sealant available for reassembly but I chose an automotive RTF @ $4 vs $24 and it worked OK. 14. Installing the seal requires some tools and experience to done successfully. The right size sockets or piece of pipe, coupled with an arbor press or vise will get the seal in. The cover is delicate so if in doubt find a machine shop. 15. Support the outside of the cover on a hard surface and with a socket or short pipe length, PRESS (don't hammer) the new seal into the gear case cover. 16. Make sure there is lubricant in the gear case. Not overflowing but maybe 1/2 full when view with cover off on a level surface. 17. Apply some RTV sealant to trhe cover and install it. Tighten bolts evenly. Light torque (1-2 ft-lb). 18. Reassemble washing machine and test for leaks and proper operation.
Our dryer would not heat and it seemed that no gas was coming from the regulator. The igniter was working fine but the burner never turned on. To check the problem, i followed the instructions to remove all body panels until I had access to the burner assembly. I dismantled both gas valve coils and tested each one for open or closed circuit using my multi-tester. I found that the three terminal gas valve coil was an open circuit and was not functioning so I ordered a new one from PartSelect and within just a couple days, had the drier back up and functioning. I also replaced the igniter due to a malfunctioning igniter that has been changed by the manufacture. I must say that PartSelect has the fastest shipping I have ever seen. One part I ordered was at my door in less than 24 hours and I only paid standard shipping...un real! OUTSTANDING....5 STAR SERVICE
I had to take the motor and transmission out. They are one piece. Removed the clutch, take off trans. cover, remove a snap ring, take the striped gear off, and put the new one on. Then put put everything back on the way it came off.
Although the motor was running, washer wouldn't agitate or spin.
After disconnecting the electrical supply, first remove the two screws at either end of the control panel and fold it back away from the washer top. Then, unplug the electrical lid switch connection. Now, remove the two clips at either end on top to disconnect the housing from the washer back and chassis. The motor is sandwiched between the water pump in the front and transmission at the rear. The Direct Drive Coupling connects the rear motor shaft to the transmisson. After you have taken the outter portion of the washer off, remove the two snap clips that hold the water pump in place and slide the pump off the front shaft. Best to also disconnect the upper hose connection so the pump can be moved out of the way. Caution though, remaining water in tub will drain out. Now remove the two screws that hold the clips in place which secure the motor to the transmission. Careful, as the old Direct Drive Coupling is probably destroyed, the clips are the only thing holding the motor in place and the motor needs to be supported so it won't drop to floor when the clips are removed. Be careful not to lose the four rubber grommets which sit between the motor and transmission bracket. After motor is on floor remove the old plastic slip-on direct drive coupling discs from both the motor and transmission shafts. The new replacement discs have steel centers which do not slide onto the shafts as easily as the old plastic ones did. I had to tap the center steel portion onto the shafts using a hammer and a deep wall socket the same width as the steel portion of the disc. Be careful! I'm sure that tapping the plastic portion of the disc to properly seat it on the shaft will break it away from the steel portion. In my case, It took me several attempts to completely seat the new discs. I had to do quite a bit of tapping to get the discs seated far enough onto the shafts so that the motor slipped easily against the transmission bracket grommets and the retainer clips snapped back into place easily. Reassembly is simply reversing the steps you took when taking the unit apart. Before putting the outter housing back in place, I checked to make sure everything was running smoothly by jumping out the electrical snap-in connection for the lid switch and running the machine in the spin cycle. Remember, if you don't jump out the lid switch and just try to test the unit in the aggitate cycle, the machine has to first fill with water.
Dryer drum would not stop spinning when door was opened
This dryer is a stackable washer/dryer. I removed all the buttons on the front panel along with the panel. I then was able to lift the front of the door and reach in to the door switch and plug. I unscrewed the old part, installed the new one. I then put the front panel and face plate back into position and screwed them back to the dryer casing. Lastly I put the knobs back on. I was extremely impressed at how easy it was to order and how quick the part came to my house. I am very satisfied with the service and the price and will use this site again in the future.
I removed the front panel of the dryer by removing the 2 screw that secure it at the bottom and pulling upward to disconnect the cover at the top. I then removed the two screws that hold the metal cover that secures the 2 elements in place. I disconnected the wire plugs from the 2 elements, removed the 2 elements and replaced them with the new parts making sure to place them in the same positions as before. I then replaced the housing cover and tightened the screws. Then I replaced the front cover of the dryer.
Initially we thought the problem was the igniter, so we ordered an igniter kit. Installed it but was unsuccessful. We then went on the websight and read further, about 50% of dryers with no heat but working had a problem with the thermal fuse.So we ordered the thermal fuse installed it, which was very easy, and success. Once the problem was diagnosed properly it was fast and easy. Recommend looking at the statistics for specific problem.
