Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism. Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires. The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.
I turned the washer on its side and felt where the leak was on the pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.
I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Unplug the washing machine. Remove screws from the washing machine control console and lift it up. Then removed medal springs that connect the back of the washing machine to the cabinet. Then removed the cabinet about 3/4 of an inch forward. Then unscrew the old Lid Switch Assembly and put in the new one. Then slide the cabinet back on the washer and screw it back together and replug it and it worked.
Disconnected old power cord inside control cabinet, removed strain relief , then removed damaged power cord. Reinstalled new cord with new strain relief.
Spider coupling between motor and transmission broken
Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy repair.
first I had to work in a closet, so couldn't get body off, just the back. The part removed and replaced really easy. Dropped a socket and a clip, had to get my reacher to get them. Difficulty was in getting the back, back on. Now everything works just fine and all the laundry is almost done.
Coupler is design to break when washer is overloaded or out of balance. Saves the motor from being burned out. Very easy repair. Unhook washer hoses and electrical plug...tip washer on side if there is no bottom to washer instead of removing side panels. Unhook clamps to water pump using flathead screwdriver. Water pump comes off without unhooking either of the two hoses. Remove 2 electrical connections and two clamps from motor using socket and screwdriver. Motor pulls out very easy...make sure you are holding motor so it does not drop onto floor. Remove motor mounting plate with socket. Remove old coupling using stubby flat screwdriver from both motor and transmission shafts. Install new coupling on transmission by placing a large socket onto plastic piece of new coupling and tapping lightly with hammer until flush with shaft. Install rubber piece of coupling...tap new plastic piece onto motor shaft using socket and hammer. Reinstall motor mount. Turn motor shaft so coupling pieces are aligned. Reverse order to reinstall motor and pump. I tilted the tub slightly when reinstalling the motor and pump as it is a tight fit...just be patient during this step.
The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.
It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.
Rotation cogs (4) worn out and the upper part of the agitator wouldn't turn with the lower agitator.
Popped the cap off the agitator (pocket Knife) Look down in the center of the agitator. I saw I needed a 7/16 socket, 6" extention and ratchet. I used 1/4" drive. I took the retaining bolt out and lifted the upper portion of the agitator off of the iower portion and out of the tub. Set the part I took out on the dryer. I pulled the cone shaped part that houses the 4 cogs pieces out of the center of the upper agitator part. Once the coned shaped part was out, turned it upside down and placed it on the closed washing machine lid, then again used my pocket knife to lift the plastic retaining ring that securely holds the 4 cogs in place upward on the cone as to remove and replace the 4 worn out cogs with the new ones purchased in a repair kit. Pay close attention the direction the old cogs are facing, so the new ones go back in the same facing direction. It can be extremely easy to install the new ones backwards. I have to say at this point, I was quite disappointed with the retrofit repair kit I purchased. The new cone part the holds the cogs and goes down into the center of the upper agitator wouldn't allow the bolt that locks the whole agitator to the shaft to line up straight and wanted the bolt to "cross" thread into the main shaft. I took it all apart again and reused the original coned shaped part that came with the machine. I should have purchased just the 4 cogs for considerably less money. Reassembled the cone part and put it back together. Reinstalled the upper agitator in reverse order of removing it. Turned on the washer and it works like it's supposed to once again. Hope this helps the next person.
I followed the online instructions to remove the shell and attempted to remove the drum, but not having the special wrench to remove the special nut, tried using a screwdriver and hammer, which failed to loosen the nut. I then started examining the the undercarriage and saw that I could replace the springs without removing the tub and did that. In the course of replacing the springs I discovered I could also access the wear pads by lifting the drum off of the undercarriage and placing a block to hold it above the pads. I was able to pop the old pads out by tapping underneath them with a hammer. The new pads were then installed and the weight of the drum popped them in. It was necessary to lift the drum assembly three times for each of the three pads.
After reading other repair stories I did it like they said. I disconnected all the hoses and drained as much water as I could. The top came apart easily with a regular screwdriver, a 1/2 in drive with extension, and a 14 or 15mm deep socket. The spanner nut came off easiest with several short, quick blows (punch and hammer, counterclockwise). In my case a good wack seemed to be soaked up by the wash tub springs. Be careful not to chip the tub.
I laid the washer, front down, onto a couple a 2x6's. I supported between the tub and body with small 2x4 scraps. The motor/trans/pump came off easily after disconnection the 2 hoses (towels handy) and wiring. After the 3 screws, and some wiggling, the assembly slid out nicely. The coupler came out after snapping the springs off to remove the pump and motor. A 1/4 nut driver and regular screwdriver assisted. Watch how the pump comes off. You might want to mark its orientation with a marker or something. Make sure you get the new coupler on all the way with some taps on the CENTER where the shaft is. Reassemble in the reverse order. You'll know why I suggested marking the water pump.
Watch the order/orientation of the springs, clips, and washer. The clips came off with a screwdriver and pliers. It's always nice to have a rag on them when removing, they like to shoot off and land in the spot that's hardest to find, like under the dryer. My clutch was assembled with the right spring and slid right on. Don't forget about the plastic washer, snap it in good. The plastic piece still on the washer was simple. I opened up a nose pliers and put it on each side of the clip then gave it a hit. It came off with minimal effort and didn't spin on the shaft like pushing on one side with a screwdriver.
During reassembly I put a very light film of grease on the shaft. That washer with the tabs gave me trouble at first. I put a good film of grease on the side with the tabs to hold it in place, with the tabs down, in the clip. Otherwise when sliding the assembly back together it comes loose and you won't get the motor/trans all the way in. Then it all has to come back out and you'll wonder what the heck is keeping the transmission from seating in all the way. You might even get it all together, figuring the motor or tub has to turn to get it to seat right. You may even try running a no clothes load and get stuck with a tub full of water. Ask me how I know.
Reverse everything to reassemble. Make sure you get the springs tight that hold the hoses on. I was worried about over tightening the plastic nut with a 1/2 drive. Run no-clothes load, large, hot with soap. I think tipping it over loosened some stuff that was stuck in between the tub and basket. No, it wasn't grease from the shaft, light film. Anyway, I'll waste a washer full of hot soapy water to avoid the, "Um..what's this on my new shirt".
I didn't mean for this to be so long winded, but I was leary about tackling this job at first. I know my way around the garage/cars, but never tried appliances before. I pictured it'd be apart for weeks and I'd have to call a repair man. Then the "I told you so" look would come. You all know what I mean. I just want to cover as much as possible and encourage others while having them avoid any troubles.
original knob had grooves inside that had worn away
Unable to get information from Part Select on how to use the part that they sent. Part had no grooves. Part Select people were very nice and offered refund but I got the directions from somewhere else. Used needlenose pliers to hold timer shaft and remove the part with the grooves. After 21 years, the shaft was very fond of the grooved part, so it took some doing but it came off. Was able to screw the new part onto the threaded shaft underneath. Success!
