11086384100 Kenmore Dryer - Instructions

Followed the instructions, removed the back cover, disconnected the top, disconnected the element and removed the element holder, then the element. Reversed procedure to install the new part.

Raised the top of the dryer then took the front of the dryer off. Took the drum off. Replaced the pulley and support rollers. Then, put the new belt on and put it back together.

Followed the PartSelect instruction video.
Basically opened the dryer.
Took the drum out.
Took the broken motor out.
cleanned the dryer since I had everything opened.
Replaced motor, pulley, old belt.
My 20 years old dryer is running like brand new.

I am a teacher and teaching is my game. I have always, with my four children, taught them to do mechanical work themselves. I and most of my children have a PhD, but in having said that, I confess, we come from a very mechanically talented family. It shows and proves to be of great benefit.
OK, so much for the intro.

I gave my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.

She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.

When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer.
Thank you so very much.
Dr Robert E McGinnis

I unplugged the dryer from the electrical outlet, removed the back of the unit and checked the heating element for continuity. There was no reading. I then removed the housing and heating element and visually inspected it. The coiled wire was broken in two places.
I then did a Google search with the model number and found Parts Select. I placed my order Sunday afternoon and the part arrived the following Wednesday. That evening it took about 20 minutes to install the new element,put the back on the dryer and re-attach the exhaust tube.
The old dryer is as good as new again.
TJ in Boise

10 min. job, easy to do / two screws top and two inside front / remove old parts install new.

I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made more in change than the belt cost!

Overall an easy repair. Belt came with diagram for easy threading the belt.

Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

It required no tools, just take out the old torn filter and slip in the new one. I should have ordered it a year ago, with the ease of the website and the delivery via Fed Ex. super easy.

turned off the power and removed the back cover, checked the thermal fuse had no continuity. ordered new part. very easy Installed the new thermal fuse,.replaced the cover, turned on the power and worked fine.

I followed the video. So easy..

found a video online and followed the instructions. First unplug dryer, then take off back cover with a 1/4 inch socket unscrew the 5 screws from the cover and remove back. Then with a ohms meter you have to check to see what terminals are bad. In my case it was the heating element. So, next you go to top of dryer and unscrew the lint trap so you can lift the top of dryer and remove the bracket holding the housing where the element is located. First take off the leads that are connected to the element and housing unit. Then gently lift housing unit up off the hinges and pull it out. Then turn over and there is another screw that holds the heating element in. After unscrewed the element pulls right out and then just put new element in and reverse everything.

I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.

Step 1: Unplug the unit, then remove the lint screen and then remove the two screws beneath the lint screen cover. Step 2: At the rear of the dryer there is a small protective metal panel near the upper part of the dryer - remove this first; then at the front of the unit, insert a plastic pry tool between the front edge of the top and the front panel of the dryer and gently pry the top loose. Step 3: Lift the dryer top up and either remove it entirely or let it rest on the back edge and a wall for support. Step 4: On the inside of each side panel near the top front, locate the two screws holding the sides of the dryer to the front panel and remove them. Step 5: Carefully slide the front panel up so that the panel detaches from two metal clips holding the front panel onto the side panels. The drum will likely drop down slightly at this point since it is no longer being supported at the front. Step 6: On the front panel there is a wire that connects the front panel door switch. I left that intact because it was too difficult to remove without risk of breaking it and instead simply set the front panel to the side of the dryer - but if possible remove disconnect the wire and then set the front panel aside. Step 7: Remove the drum by pulling it out, inspect the back felt seal for wear and also the plastic split ring bearings at the front end. When you remove the drum belt the tensioner pulley underneath the drum will likely fall over, but this is to be expected because without the belt and drum providing tension, the piece only fits loosely in a slot at the bottom of the dryer. Step 8: Inspect the drum rollers, motor, and other parts for wear, then vacuum out the inevitable lint and dust inside the unit. Step 9: At this point I also decided to inspect and clean out the lint chute at the back of the unit, so I removed the protective back cover and removed the screws holding the lint chute in place. I then cleaned out the lint that builds up over time inside the chute and checked the two foam lint chute seals at the back of the unit - these needed replacing so I removed the old deteriorated foam and vacuumed off the back of the unit and then adhered the new seals to the back of the dryer. Step 10: Take the new multi-rib belt and drape it around the drum with the ribbed side against the drum - you will likely see a mark around the drum where the old belt was positioned, so use that as a guide. Step 11: Since one of the split ring bearings on my unit was worn, I replaced both at this time by simply pressing the plastic tabs out of the slots at the front of the drum, removed each half of the ring, and reinstalled the new parts - they only correctly fit one way so that the plastic edge lines up cleanly with the front edge of the drum. Step 12: With the felt drum seal toward the back replace the drum - I used a small box to support the drum upon while I reinstalled the drum - this will make it much easier to manipulate the belt around the tensioner and motor. At this point I reached underneath the drum and reinstalled the tensioner. by positioning it in the two small slots near at the bottom panel that are near the front of the dryer motor. Then take the belt and pull it through the tensioner and around the motor pulley at the front of the unit. You will likely have to push up slightly on the drum and tensioner to allow the belt to be pulled through the tensioner and around the motor pulley. Step 13: Rotate the drum slowly by hand at least one full revolution and check to see that the felt seal at the back is not pinched and that the belt does not fall off the pulley. Step 14: I removed the box supporting the bottom of the drum, then took the front panel and fit the front of the drum against it so that the split ring bearing matched up to the front panel. Step 15: The drum will still be somewhat loose and that allowed me to carefully lift the front panel up and then slide it down back onto the two metal clips that hold the front panel to the side panels. Step 16: Reinstall the two screws that also hold the front panel to the side panels. And if you also removed the wire connection to the dryer door, reattach that too. Step 17: If you removed the lint chute, reinstall it from the back while the lid is still off so that it is easier to slide it into position. Step 18: Reattach the top of the unit by seating it against the top of the frame (of course if you disconnected wires, reattach those too) and reinstalling the two screws underneath the lint screen cover. Step 19: Reattach the rear panel cover and small protective metal panel. Step 20: Reattach the flex-hose to the lint exhaust.