UNPLUG THE DRYER!!!!! First removed the two screws holding the lint filter in place. Then slipped a screw driver between the top and the dryer body to remove the top. Using a nut driver removed the two screws holding the front of the dryer in place, remove the two wires for the door switch., lift the front cover of the dryer and set it aside. Support the drum ( two extra hands would be nice) and remove the drive belt. Then remove the drum. A thorough cleaning to remove all of the scorch like stain from the drum and back plate. Remove the seal and glue the new one in its place. Put it back like you found it. Make sure that the seal is not tucked against the back plate. Dryer works better than new and no more stains.
The most difficult part of this repair was making sure I purchased the right part !!! Part Select.com has a great website with pictures of almost every part you could ever need. I was able to select the right part and from there the repair was easy.
I took the dryer apart by visually looking at it and removing screws, etc. until I had the top off and the front off. I took the dryer apart so I could get the part out and use it visually ascertain I was ordering the same part.
I bought the replacement part and only then did I have the instructions to take the dryer apart. It was further apart than the instructions said. I had to take the front off to retrieve the broken part which had fallen inside the front of the dryer.
I put the front back on the dryer and installed the new part, which, fortunately could only be installed one way. Once I had the two screws tightened into the part, the remainder was to simply follow the instructions that came from your web site and put the link filter and top of the dryer back on. Of course, I plugged in the dryer and checked to see that it ran before completing this.
I am amazed that I was able to find this part for a 30 year old dryer. The part hasn't changed at all. I guess, if you have a good part, there's no need to modify it.
Dryer hummed but drum wouldn't turn unless helped.
Solution: electric motor replacement as the integral centrifugal switch lever (plastic cam) wears over time causing the start windings' switch poor contact. Took it all apart, (back panel, front and top) including lifting the drum out to completely expose the motor. Needed to wrench the plastic fan from the inside motor shaft. Tricky part was swapping the original pulley (6 rib belt, still good) for the one supplied for 4 rib belts. I needed to file another flat onto the other side of both motor shafts (old and new) to break them free, using a vice to secure the pulleys. The dryer works perfectly! It's a great dryer that can be repaired by a determined novice. The enclosed instructions were helpful, although if followed about cutting the original motor shaft to obtain its pulley might require drilling the shaft from the pulley = nonsense. Thanks again Parts Select.
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
8 of 10 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My Kenmore dryer door catch was worn out, so the dryer door wouldn't stay closed, and I was unable to dry my laundry.
I identified the correct catch of the three that were included in the package by matching its number to that on the old catch that I had pried out of the door using a flat screwdriver. I centered the new catch over the square hole in the door and pressed it into place. Then I used some needle-nose pliers to twist and remove the metal pin that fits into the catch from the main dryer housing. I replaced that with the new piece included in the kit, gently tapping it into place with a hammer. The repair complete, the door worked perfectly. Thanks for your help and for the speedy delivery of the kit.
Extremely easy repair! Unplug the dryer. Remove the lint trap screen. Take the two screws out of the lint trap chute, pry up the top of the dryer, insert wood or have someone hold top up, remove two screws holding the switch in place while holding the switch so the old spring doesn't fall. Remove old spring and replace with new one. Re-attach switch to dryer with two screws. Plug in and test run. Lower top and push firmly to engages clips. Re-install two scres in lint trap chute followed by the lint trap screen and you are finished!
Repair took about five minutes and saved approximately $70!
I order a new belt and I watched the video instructions on how to replace it, follow the instructions, removed the top and took out the dryer tumbler or can, found a broken idler pulley, order a new one, got it in about two days, replaced all the parts and now its working like a new dryer, I called several repair shops and I got estimates from $65 to $150, I spend less than $35 and it took me about 35 minutes to install and I got it fixed..
Start windings burnt out on original motor (dryer would not start)
The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to unthread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.
1) Unplug power cable from dryer. 2) Remove the 2 screws that secure the chute for lint filter screen with Phillips head screwdriver. 3) Remove the lint filter screen. 4) Depress plastic locking clip on each side with putty knife to release tension and lift up top panel to clear the locking clips. Each locking clip is located 2-1/2 inches from the front edge of side panel. 5) Lift the top panel and lean against the wall for support. If dryer top panel cannot be raised all the way due to cabinet(s) above, tape the dryer top panel to cabinet above or have somebody hold the top panel for temporary support. 6) Install the new metal locking clips. Ensure that the elongated tab of the metal locking clip is towards the front of dryer. Compress locking clip lightly with pliers and push down into the hole. 7) Lower the dryer top panel and press it down in place over the metal locking clips for a tight fit. 8) Reinstall the 2 screws to secure the lint filter chute. 9) Reinstall lint filter screen. 10) Reconnect power cable for dryer. 11) Turn on dryer and inspect that all dryer panels (top, sides and front) are tight and secured. Repair Duration: 5 minutes
Door springs and cables were broke, and the door catch was broke.
Removed screws by lint trap, used putty knife to pry top of dryer apart, use nut driver for two bolts that hold the front panel of dryer on, replaced parts, put it back together.
The dryer was squeaking and would not heat at all.
The first thing I did was call my friend Donnie who manages some apartment buildings and who is always complaining about fixing things and getting the right parts to fix things. He told me what to order from PartsSelect and when the parts got here I called him up and he did the repair work.
He was reluctant to do the work at first but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!