Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Light didnt go on
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
i followed the online instructions on how to take the icemaker apart, which were very easy to follow. Once the new part arrived it plugged right in and a few steps later it was back together. within the hour we were hearing the sound of ice dropping into the tray. thanks for all the help this definitely saved us money and hopefully we get many more years out of this icemaker.
Removed the one screw holding the unit in place in the freezer and pulled it out. Removed the 3 screws that hold the motor in place on the ice maker. Replaced the motor unit, replaced the 3 screws, and re-installed the ice maker. Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here for $65.
ice maker gears stripped/ bearing & cup assy broken
The bearing & cup assembly was broken and the gears in the drive assy were stripped. Unfortunately I couldn't find anywhere to buy the gears without buying the entire motor assy with the gear box already on it. Cost was up to $85 with shipping but at least it now works fine.
To repair: a 1/4 nut driver will take off screw below ice maker and all you need to do is loosen the 2 screws above the ice maker then push it upward slightly and it will slide off the top 2 screws. Then pull the power connector off from behind the ice maker at the side of the refridge. Then pull straight out and it will slide off the water fill tube. Now with unit out of refridge I took the cover off the front of the ice maker and removed the 3 philip screws. I then pulled the motor/gear assy off from the chassis of the ice maker. I then had to remove the 2 philip screws on the chassis (under the motor/gear assy) to remove the cube maker/element from the chassis. This allowed me to remove the rotating cube spatula bar to replace the filler cup/bearing assy. Then I reinstalled the spatula bar and the 2 philip scews on the chassis to the cube maker/element assy. I then installed the new motor/gear assy to the chassis and installed the 3 remaining philip screws. Put the cover back on the ice maker and inserted assy back into the refridge by first reattaching the power connector and then sliding backward onto the water fill tube and then slipping over the top of the 2 top screws on the refridge. Then I installed the screw below the ice maker and tightened all 3. Presto - repair done in 30 minutes and perfect cubes were spitting out within the hour.
The coating on the mold /heater unit as cracked and some broken off and cause the water to drip down in the Ice trace and form large icicles
I just removed the unit and replaced the mold/'heater with the new one and re-installed. It was very easy and didn't have to turn off the refer. or empty the frozen food. However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons Jim
I first did a diagnosis of the optical cuircuits and found them good. The tray heated up and when resetting the moor controller, the water cyccled to fill the tray so the only other thing it could be was the motor controller.
removed the service door for the ice maker I removed the wire protectore screw and shroud pulled the icemaker unit out and unplugged the unit removed the motor controller end cap unscrewed 3 screws holding the motor controller removed and replaced the motor controller. ensured that all wire harness connector poiints were solid reverse the above instructions and in 5 hours I was getting ice again!
$90 turned out to be a savings from the $250 it would have cost to have someone come out and look at the fridge.
I highly recommend to anyone who can read and use a screwdriver to perform this repair if you have diagnosed this as the root of your problem!
I Removed 3 screws, pulled off the plate and put the new one on, screwed in 3 screws and away I went. I could not believe how easy it was to order the part and how quickly it arrived. I was very pleased. And I was literally screaming with excitement when I heard the first set of ice cubes drop!
I removed the icemaker. One screw at the bottom and then unplug the electric. Remove the old motor from the face that has 3 screws holding it. Put the new motor in. A very simple job. I now have a full ice bin by the next morning.
The icemaker on the refrigerator had stoped working.
Repair was real easy, I had to remove several screws in the bottom of the icemaker module housing. The unit slide out with no problem there was a wire assembly that hat to be disconnected but this did not present a problem. The old module came out real easy after removing 4 screws and the replacement was not a problem to but in.
The plastic water fill tube got cracked when we moved. I called a parts company and they told me they couldn't just sell me the tube I would have to buy a whole kit for about $50 dollars. I decided to glue the tube. It worked for a while then it started leaking. So I thought I would have to buy
I hand screwed the fill tube into the water tube and stuck it into the freezer hole. I screwed the fill tube to the back of the refrigerator.
Thought The issue was the solenoid valve. Took a lot of research but finally found through parts select. Perfect match and easy to install, but unfortuantely, it did not solve the problem of poor ice production. Now would appear that the icemaker itself needs to be replaced.
Removing the ice making assembly from the Ice compartment was not difficult except that two of the 3 screws we not visible without a mirror and then my nut driver was 5" long making it very tight quarters, so it was a time consuming process to remove them. Once the 3 screws were removed the wiring harness was easily disconnected and the whole assembly came out. The next step was to figure out how to remove the faulty part from the rest of the assembly. After some strong persuasion the part would not separate from the control Assy. (The front of the unit) To complete the job I had to pull the front cover and unplug the motor and heater assy to expose two additional screws that had to be removed to pull the defective part out. The reassembly went quite easy except the 2 screws that you need a mirror to see. I was also trying to hurry because the frozen items were not holding all that well after the door was open for about an hour and a half. An instruction sheet showing the steps would have cut the time over 1/2!
first i removed 1 screw, then pulled out the ice maker, unpluged the electrical wire, i removed the white plastic cover , then an additional 3 screws . i pulled off the ice maker control . replaced with new ice maker control. i repeated the steps to put back the ice maker ...so super quick part delivery !!!
