Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Light rocker switch broke and refrigerator light couldn't go on.
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
I removed the ice bucket and dumped the ice (saving part of it to put back into the bucket after repair).Using the nut driver,removed all screws,rmoved the auger that the broken drum is mounted on.I reoved the nut on the end of the auger(with my pliers).Slid out auger removed broken drum,replaced new drum and re assembled using your easy to follow instructinns.
The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.
Dryer made loud intermittant humming sound after 20-30 minutes of use
Unplug Dryer. Remove 2 5/16in hex screws from lower panel and remove panel.Remove 3 5/16in hex screws attaching lint duct. Remove 8 1/4in hex screws attaching blower housing. Remove 2 1/4 hex screws attaching thermostat to blower housing. Using adj. wrench on back of motor shaft nut to hold, loosen fan assy. w/ 7/8in socket. Remove 3 5/16in hex screws holding fan housing to motor mount. Remove 2 5/16in hex screws holding housing and motor mount to base floor. Push belt pulley wheel up enough to loosen belt and take off rear motor pulley. Motor w/mount can be slid out bottom for replacement [wires are layed toward front].Using 6in flat tip screw driver press down to unlock front & back motor bushing holddown clamps. Pinch electrical wire connector ends to pull off old motor. Remove and Install new motor, reversing steps. Belt replacement [suggested w/new motor] requires removal of 2 5/16in screws to lift/remove door w/front panel [disconnect door switch wires upper right rear corner].Remove 4 5/16 screws holding front bulkhead. Once bulkhead is pulled up and off, allow front end of drum to sag and rest IN PLACE [removal not required to slip old belt off and install new belt]. Note belt location point around drum. Slide new belt on. Reinstall bulkhead and panel/door [Don't forget door swich wires]. Adjust belt into position and push spring-held belt pully up to allow looping of new belt around rear motor belt pulley. Complete w/hand turning of drum to ensure belt is aligned and feeding properly. Reinstall lower fan housing/covers/thermostat,etc removed for motor installation.
I removed the 4 screws holding the front cover in place. Removed the 4 screws holding the ice auger cover in place. Removed the c clip holding the auger on the shaft. Pulled out the auger shaft. Removed the broken auger drum and replaced with the new one. Reassembled in reverse order.
Not so easy as others have described. I kept the parts off the auger together in my hand as I replaced the drum. Thanks to the people who mentioned the nut being left handed. Taking a picture before dis-asembly saved me. I would never have gotten it back together otherwise.
Took the Ice Bin Out emptyed it then removed the nesasary screws pulled the broken Peice off and sliped the new part on held the metal peices together so we would know how to keep them in order for fear of putting them in wrong place but we did it now it works great thank you so much for getting the part to me so quickly your great.
This was not a hard repair. Just remove all the screws and slide out the old Auger drum. It is always good to take a picture first incase you have any problems putting it back together. Be careful to put the ice crushers back in the same order and make sure you look at how the "door spring" connects before pulling it apart.
First I removed the 6 screws and then 2 more--being carefull to take cap off inside to nremove metal blades--be sure to keep in order--taking ba digital picture helps at this point--make sure to put back nin reverse order after replacing washer and new auger--went smooth thanks appliance parts repair service forum--Rick--Enjoy your own repair!!!
I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.
Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place
