Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 4 at 11:59pm EST.
Cub Cadet Chipper Shredder Starters
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Cub Cadet Chipper Shredder Starters
Cub Cadet Chipper Shredder Pulley/Spring Assembly
PartSelect Number PS8988822
Manufacturer Part Number 498144
Cub Cadet Chipper Shredder Starter-Rewind
PartSelect Number PS8981884
Manufacturer Part Number 497680
This recoil starter is for lawn and garden equipment engines.
Recoil starter spins the crankshaft to start the engine when you pull the rope.
Installation Instructions
Seikai from MARICOPA, CA
starter rewind cord broke
I found the model number of the Briggs & Stratton engine on the inside of the engine housing. Ordered a new starter-rewind unit, as the old cord broke and the thing was well worn. The instructions were clear enough, but to get the old starter off I had to drill out four rivets, which just spin around when you try. I used a hacksaw, chisel, pliers, whatever worked on each rivet; this took a while. When they were finally removed, the new starter pull unit was relatively easy to install with the small nuts and bolts provided. On the Yard Machines log splitter, putting back the engine housing is quite tricky; you have to jostle the thing into place, get the pull handle above the cover and line up the bolt holes.
Read more...
Cub Cadet Chipper Shredder Clutch-Starter
PartSelect Number PS8968281
Manufacturer Part Number 399671
Cub Cadet Chipper Shredder Plate-Pawl Friction
PartSelect Number PS9074726
Manufacturer Part Number 692299
Cub Cadet Chipper Shredder Starter-Rewind
PartSelect Number PS9983381
Manufacturer Part Number 591301
Installation Instructions
Wayne from OOLTEWAH, TN
Parts fit like a glove
Removed pull start assembly down to the crank. Installed motor housing, motor fan & rewind assembly. All went real good.
Read more...
Cub Cadet Chipper Shredder Starter-Rewind
To replace the pull starter/recoil assy. Remove low oil warning light, and air filter housing then remove the 4 bolts holding the front cover. Once the front cover is free remove kill switch wire
Drill out the rivets holding the recoil housing w/ 3/16 bit. Screws w/ nuts are included to use in place of rivets, I used red Locktite on the screws which hold the started recoil to the front cover. Make sure the pull rope is correctly oriented in the 11:00 position. Replace front cover, four bolts. Air filter housing, kill switch wire and low oil warning light Read more...
PartSelect Number PS9064480
Manufacturer Part Number 693900
Installation Instructions
Dennis from EUFAULA, OK
Gas tank leaking, pull starter rivets worn, rope and rope bushing worn
The gas tank was a simple job, close the fuel shut off, remove fuel hose then back out 2 bolts on the mounting bracket. Reverse procedure to mount.To replace the pull starter/recoil assy. Remove low oil warning light, and air filter housing then remove the 4 bolts holding the front cover. Once the front cover is free remove kill switch wire
Drill out the rivets holding the recoil housing w/ 3/16 bit. Screws w/ nuts are included to use in place of rivets, I used red Locktite on the screws which hold the started recoil to the front cover. Make sure the pull rope is correctly oriented in the 11:00 position. Replace front cover, four bolts. Air filter housing, kill switch wire and low oil warning light Read more...