Make sure you haven't got the discount earlier.
VALVE W10599356
Rated by 5 customers
Really Easy
30 - 60 mins
Ratings submitted by customers like you who bought this part.
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
disco the water lines
removed the back of the washer then removed the top.
remove leaking water valve by removing the hoses then removing the valve assembly.
replaced with new,checked for leaks
reassembled washer
-
Tony from SMITHTOWN, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
- Turned on a quick cycle to drain any water left in the pipes. Once no water was coming in I turned off the unit.
- Unplug the unit.
- Remove the cold and hot water lines from the back of the unit. Keep a bucket and towels nearby.
- Remove the 3 screws from the back to rem ... Read more ove the lid.
- Pull lid back about a 1/4" and lift up.
- The valve is located at the top rear where the water hoses attach to.
- Using plyers, remove the plastic clips from the valves holding the wires. Remember the location, you will re-attach those clips onto the new valve.
- Remove the single screw holding the valve on the back of the unit.
- Slide the valve just slightly and pull it inward towards the inside of the unit.
- Remove the electronic connections by pulling on the connectors. Remember the locations as you will re-attach them onto the new valve.
- Remove the two hoses that go to the detergent container. Using plyers to squeeze the metal retaining clip, slide it back, then pull the hose off. Do this for both hoses. Remember which hose goes to where.
- At this point, just reverse these instructions to install the new valve starting by attaching the new hoses to the detergent container.
- Then attach the electronic connectors.
- Attach the valve with the screw to the unit.
- Attach the wire clips back onto the valve.
- Attach the hot & cold water lines
- Turn on the water lines and check for leaks
- Plug unit in.
- Run a quick cycle to again check for leaks inside and outside.
- Replace the lid
- Re-install the 3 screws holding the lid.
-
Tim from Irvine, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
2. Remove three screws on back of washer for top cover.
3. Slide top cover back 1/2-3/4 inch and remove from machine
4. Remove water inlet valve set screw to left of hot water supply connector.
5. From the inside of the washer, sli ... Read more de the inlet valve to the left, disconnect wiring, and wire clips.
6. Disconnect hoses from back of detergent dispenser.
7. Connect hoses from new inlet valve to back of detergent dispenser
8. Connect wiring, and wiring clips to new inlet valve.
9. Slide inlet valve back into place and install set screw.
10. Replace top cover and install three screws for top cover
11. Recommend replacing supply hoses (mine leaked, and were approx. 5 years old).
12. Install water supply, turn on water, check for leaks. Plug in washing machine.
Video demonstration: https://www.youtube.com/watch?v=yH0TppbTtI0
-
Andy from CENTERTON, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
To replace the valve you need to first shut off the hot/cold water supply and remove the hoses ... Read more . (I took this time to replace the several year old hot & cold water supply rubber hoses with metal braided hoses. I also took a wire brush to the threads of the copper spigot removing any built up corrosion or gunk.) Next you need to remove the 3 1/4" sheet metal screws which secure the top panel of the washing machine. I always take a few pictures of the old part, hose, and connectors just to make sure I replace them in the same locations.
After removing the cover you can use clamp removal/installation pliers, vice grips, or a similar tool to remove the clamps for the hot and cold water to the detergent/bleach/softener dispenser.
Then, remove the electrical connectors on the valve and if you want label them with their locations on the left or right facing the rear of the washer if you want but they are pretty much self-explanatory. They have little retention clips which need to be disengaged in order to be removed from the valve assembly.
Next, remove the hoses and then the three sheet metal screws attaching the valve to back panel of the washer. Install the new valve assembly and then attach the hot and cold water hoses using the clamps to the detergent/bleach/softener dispensers. Then, attach the electrical connectors to the new valve and listen for the clip to engage and gently pull back on the connector (not the wires) to ensure they are properly attached to the valve.
Reconnect the hot & cold water supply hoses from the building pipes and turn-on both spigots or ball valves. Check for leaks and then plug in the washing machine and run a load to test the normal operation. I would leave one piece of dry clothing in the tub after running a load and leave it for a few hours to ensure the new valve is working as advertised.
If there are no further leaks, you are done! Way to go!
-
Jay from SAINT PAUL, MN
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Socket set
-
Nicholette from Antioch, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
- < Prev
- 1
- Next >
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
6 people found this helpful.
2 people found this helpful.
1 person found this helpful.
1 person found this helpful.
- < Prev
- 1
- Next >
Manufacturer Part Number: W10599356
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.