Make sure you haven't got the discount earlier.
Timer WD21X10013
Rated by 10 customers
Easy
30 - 60 mins
Ratings submitted by customers like you who bought this part.
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
- < Prev
- 1
- Next >
-
ALFRED from OWENSBORO, KY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
Turn off power for unit at breaker box. Open the front door and remove the screws holding the front cover. Locate timer. Unplug timer and remove screws holding timer in place. Reverse process to install new timer.
Drain solenoid - (a little harder):
Turn off water to dishwasher under sink and disco ... Read more nnect from plumbing. Disconnect drain line. Remove any screws holding dishwasher in place and start pulling unit from it's cavity. It should come about half way out. At this time you can peer under the unit and see the drain solenoid.
If you don't know what you're doing (like me) I recommend the following. Remove the water line from the dishwasher (and possibly the drain line) It should now be easy to pull the unit all the way out and tip it on it's side, fully exposing the drain solenoid.
Note: The drain solenoid provided to me was encapsulated in a different bracket than the original one in my dishwasher unit. It was necessary to pry the solenoid out by bending the bracket and installing in the original bracket. Then squeeze back together in a vice with a few gentle love taps with a hammer to squeeze it all back together. It was still a little loose but the solenoid just goes up and down so no big deal.
There's a little metal clip holding the white plastic arm to the drain valve. Let's say this O represents the diameter of the metal rod it's hooked to. That clip is removed by a small screwdriver pushing the clip away from that rod, this way: 0 ==> It will make sense once you do it.
From there it's pretty easy to replace the solenoid unit and reverse the steps above to re-install the unit.
Chris
-
Chris from West Bloomfield, MI
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Wrench set
i couldent use the hole unit because it was for a dryer.
i new the motor would work because it had the same gear and rpm. i couldent find a motor no wear.
-
Manuel from Carteret, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Turns out the motor is really easy to remove, just pry the metal latch out a bit with a flat screwdriver and out it comes. We put the motor from the new timer on our old timer, and presto, everything works!
Like other reviewers said here, pop off the seven screws and the interior door panel comes right off. Disconnect the power plug, signal plug and ground plug and reverse the procedure. Really easy repair. Make sure you shut off the fuse panel before starting the repair.
-
Jim from Raleigh, NC
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
-
Jeffrey from Kernersville, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
-
greg from nashville, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
-
merritt from venice, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
-
Lance from Seattle, WA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
-
Crystal from Madison Heights, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Disconnected power leads to timer then removed the two screws that held the timer in place.
Installed new timer in revers order.
Also replaced the door gasket, one door liner screw, and the vent pad.
... Read more >The most difficult part was keeping the door latch mechanisim in place when reinstalling the door liner.
-
Tim from San Pedro, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
- < Prev
- 1
- Next >
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
2 people found this helpful.
1 person found this helpful.
- < Prev
- 1
- Next >
Manufacturer Part Number: WD21X10013
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.