Make sure you haven't got the discount earlier.
SEAL FOR F 314286
Fits your DE110 Dryer!
Rated by 1 customer
A Bit Difficult
More than 2 hours
Ratings submitted by customers like you who bought this part.
Fits your DE110 Dryer!
PartSelect Number PS2032187
Manufacturer Part Number 314286
Manufactured by
Whirlpool
Troubleshooting
This part works with the following products:
Dryer, Washer Dryer Combo, Range.
This part works with the following products:
Maytag, Jenn-Air, Caloric, Roper.
Part# 314286 replaces these:
AP4038894, 491582, 3-12902, 3-14286, 312902, 314286, Y312902
Customer Repair Stories
Average Repair Rating: 2.0 / 5.0, 1 reviews.
What's this?
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Motor Frozen; would not turn
MAJOR MOTOR ISSUE: Motor would attempt to start, but the shaft would not turn. The cause was a build-up of lint that was jammed between the armature and field. The fix was the patient use of compressed to blow out the motor, and a light application of wd-40 onto the shaft where it emerges from the housing at each end. I had fully inte
... Read more
nded to replace the motor; and after removing the wires, the fan from the shaft and the motor from the bracket holding it tried the above and it worked. The fan was stubborn to remove from the motor shaft, but a light application of wd-40 enabled it to slip off without resistance.
After testing the newly cleaned motor (starting, stopping, running without getting warm) I concluded that it was still turning freely and basically ok. There was no slop in the armature bearings. I ordered a new belt and door seal and reinstalled everything after thoroughly removing the dust and lint that coated everything. I also paid careful attention to the ductwork—I used duct tape to seal the connections & hopefully should be set for another 20 years or so. The disassembly and re-assembly instructions on this web are excellent and should be read carefully before starting the job. The purpose here is to help people save motors that are just clogged with lint.
After testing the newly cleaned motor (starting, stopping, running without getting warm) I concluded that it was still turning freely and basically ok. There was no slop in the armature bearings. I ordered a new belt and door seal and reinstalled everything after thoroughly removing the dust and lint that coated everything. I also paid careful attention to the ductwork—I used duct tape to seal the connections & hopefully should be set for another 20 years or so. The disassembly and re-assembly instructions on this web are excellent and should be read carefully before starting the job. The purpose here is to help people save motors that are just clogged with lint.
Read less
Other Parts Used:
-
Stephen from Rye, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
3 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Back to Top
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kenneth
April 4, 2022
Is this the felt gasket that the drum rides on.
For model number LDG312
Hello Kenneth, Thank you for your inquiry. We show that this part is the front panel seal that prevents air from leaking between the front panel and dryer drum. The seal for the model number that you have provided that allows the drum to glide smoothly is PS11740771 for the beige drum, and part PS11741149 for the gray drum. The high temperature adhesive is part# PS11757492. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Back to Top
You May Also Need
?
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2032187
Manufacturer Part Number: 314286
Manufacturer Part Number: 314286
Brand
Model Number
Description
Back to Top
SEAL FOR F
$
62.13
Special Order
✖
Stock Status
In Stock
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.