Make sure you haven't got the discount earlier.
Drive Belt 134051003
Fits your FWFB9100ES1!
★★★★★
★★★★★
Rated by 5 customers
Easy
30 - 60 mins
Ratings submitted by customers like you who bought this part.
Fits your FWFB9100ES1!
PartSelect Number PS1990787
Manufacturer Part Number 134051003
Manufactured by
Frigidaire
Product Description
Drive Belt Specifications
This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Frigidaire Washer Drive Belt
Back to Top
Troubleshooting
This part fixes the following symptoms:
Will not agitate | Burning smell | Spins slowly
This part works with the following products:
Washer.
This part works with the following products:
Frigidaire, Kenmore, Crosley, Electrolux.
Part# 134051003 replaces these:
AP4321740, 1378564, 134051001, 134051002
Customer Reviews
Average Rating:
4 Reviews
★★★★★
★★★★★
3.8
Filter By Rating:
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Melissa B - March 13, 2023
Verified Purchase
worked great
The right part and received quickly easy to install and the washer works like new again.
★★★★★
★★★★★
David P - December 10, 2021
Verified Purchase
back up
I punched this to have then it is needed.
★★★★★
★★★★★
Ron G - January 8, 2019
Verified Purchase
Easy repair
Website video instructions were accurate, easy replace and install
★★★★★
★★★★★
George P - April 18, 2018
Verified Purchase
Did not work
New belt did not solve problem. Washer still does not spin.
- < Prev
- 1
- Next >
Back to Top
Customer Repair Stories
Average Repair Rating: 3.3 / 5.0, 5 reviews.
What's this?
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Washer will fill and drain but will not spin or agitate
Went by the percentage of people with same problem- door switch was the highest. Ordered door switch and a new belt (belt was getting worn- 6 yrs. old) Door switch did not fix problem. Saw on website that it could be motor control board. Took motor control board out. Nothing visible wrong with anything. Decided not to spend $$ on new boar
... Read more
d. Figured new washer would be better. Put motor control board back in and tried it......works like new! Must have been a loose wire on the motor control board. Next time I will check wires first. :) Getting motor control board in and out was time consuming but no too hard.
Read less
Other Parts Used:
-
Gabriel from MERRILL, WI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
16 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drum pulley kept getting loose and wobbling. Hub wore out making permanent tightening impossible
Simple. Remove the drive belt from the pulley. Next remove the retaining screw and remove the old pulley. Put the new pulley on the hub, then insert the retaining screw and tighten securely. Last, replace the belt over the motor and hub pulley. This was the most difficult part as the new belt was quite tight. But once I convinced mys
... Read more
elf it was the right belt a little more effort yielded results and the belt fit fine.
Read less
Other Parts Used:
-
Richard from Long Valley, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
11 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no spin, broken handle, everything else worked
after clearing shelving. It took about 20 minutes to remove the dryer stacked on top, along with the gas line and the vent hose.....
Two screws and gently pry the back up with a screwdriver and the top pops off. open the door and remove the 2 screws while reaching down inside and the switch come right up with its 3 plug harness.
... Read more >swap the old switch unit for the new one and slip it back down into place and reinstall the screws, and done in about 15 minutes.
my belt is in good shape so I will save the one I bought for later.
the handle is 2 screws and took less than 2 minutes.
It took about 20 minute to put the washer/dryer units back together and against the wall and running
Two screws and gently pry the back up with a screwdriver and the top pops off. open the door and remove the 2 screws while reaching down inside and the switch come right up with its 3 plug harness.
... Read more >swap the old switch unit for the new one and slip it back down into place and reinstall the screws, and done in about 15 minutes.
my belt is in good shape so I will save the one I bought for later.
the handle is 2 screws and took less than 2 minutes.
It took about 20 minute to put the washer/dryer units back together and against the wall and running
Read less
Other Parts Used:
-
Paul from Fontana, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
5 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door lock switch faulty preventing washer from spinning
Codes did not point directly to the door lock, so that was a 50/50 between door lock and control board. With top of washer removed door lock is just a couple screws and 3 electrical connections.
Belt was worn and frayed. Belt replacement was tricky because new belt was so tight. Used vice grips to lightly hold belt on pulley ... Read more while using screwdriver through spokes into tub back to ratchet/control pulley. Not too bad.
Works like new!
Belt was worn and frayed. Belt replacement was tricky because new belt was so tight. Used vice grips to lightly hold belt on pulley ... Read more while using screwdriver through spokes into tub back to ratchet/control pulley. Not too bad.
Works like new!
Read less
Other Parts Used:
-
Jeff from Thousand Oaks, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
44 of 55 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
belt was still on washer, had developed a loose tear
Very easy to replace belt on this model, belt had spilt and the loose rubber was flopping around and dislodged plug from water pump. Washer would not start cycle, display showed (no spin). Removed back access panel with screwdriver. Spin the pulley and slip belt off pulleys. New belt is very tight but it will go on, no tension adjustme
... Read more
nt on this model. Thanks part select quick service will order again from this company.
Read less
-
jeffrey from mount juliet, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
7 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Back to Top
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Back to Top
You May Also Need
?
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1990787
Manufacturer Part Number: 134051003
Manufacturer Part Number: 134051003
Brand
Model Number
Description
Back to Top
Drive Belt
$
38.67
On Order
✖
Stock Status
In Stock
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.