Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
Door Boot Seal WH08X10036
Rated by 13 customers
A Bit Difficult
1- 2 hours
Ratings submitted by customers like you who bought this part.
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Door Boot Seal Specifications
How Buying OEM Parts Can Save You Time and Money
Replacing your General Electric Washer Door Boot Seal
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
- < Prev
- 1
- 2
- Next >
-
Jodd from HANNIBAL, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
I only ran into one issue not included in the video. In order to remove the inner ring holding the boot seal, I had to remove the weight at the bottom of the tub. This is easy to remove with a wrench, but took two people ... Read more to reinstall. You only need the second person for 1-2 minutes to hold the weight while you align the bolts.
The most difficult part is ensuring you replace the hex nuts and screws in the same location. I took pictures as i removed them to know where to reinstall.
Total repair time was probably 1.5 hours.
-
Paul from LAKEVILLE, MN
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
-
Janet from BRIDGEPORT, WV
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
-
Gary from WEBSTER, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers
-
albert from CLIMAX, NC
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
-
nicole from round lake beach, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
-
Gerard from Pompano Beach, FL
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
-
Patrick from Linden, NJ
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
ben from newaygo, MI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Unsure of how to replace the gasket, I used a phillips screwdriver to pull the door and front panel ... Read more off. I thought that this would be pretty simple, but I soon discovered that it wasn't as simple as removing several screws and pulling the pieces off. The door was easy, the bottom panel was easy, but the front panel was held in place by screws, plastic tabs, the front of the gasket (I'll explain later), and gravity by means of plastic supports. Trying to find and release the tabs, lifting the panel up and out was not self-explanatory. I finally figured it out, and it made changing the gasket out, a breeze. The gasket is held in by two diferent wire spring clamps/bands. One band holds the gasket to the outside of the tub, and the other band holds the gasket to the front panel. Before removing the front panel you must remove the first band which is cleverly hidden by the face of the rubber gasket. Just peel it back...it's in there. I was able to pull/pry this off with a screwdriver because I was not worried about damaging the old gasket. The second band had to be removed with either a 6mm/7mm wrench(I can't remember which) or a stubby phillips screwdriver. The stubby screwdriver is handy because of the proximity of the tubs counterweights. Once the final band is removed just peel the gasket away from the tub, after taking note of how it came off. Put the fully loosened band on the new gasket and fit the new gasket into place. It helped to have two sets of hands to work it around the tub, but probably not necessary. The wrench is necessary to properly tighten the band, because you cannot get enough torque on the stubby screwdriver.Once the gasket is in place you can re-install the front panel, and secure the front of the gasket to the panel. Install the band and it will secure itself by the tension of the spring. Put the door back on and you are ready to wash clothes.
-
Brandon from Chugiak, AK
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers, Wrench set
- < Prev
- 1
- 2
- Next >
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- 2
- Next >
12 people found this helpful.
3 people found this helpful.
2 people found this helpful.
2 people found this helpful.
2 people found this helpful.
1 person found this helpful.
1 person found this helpful.
1 person found this helpful.
- < Prev
- 1
- 2
- Next >
Manufacturer Part Number: WH08X10036
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.