Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
Water Inlet Valve Assembly WH13X26535
Rated by 11 customers
Really Easy
30 - 60 mins
Ratings submitted by customers like you who bought this part.
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Water Inlet Valve Assembly Specifications
How Buying OEM Parts Can Save You Time and Money
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
- < Prev
- 1
- 2
- 3
- Next >
- < Prev
- 1
- 2
- 3
- Next >
- < Prev
- 1
- 2
- Next >
Take pictures of where the wires go so you can remember for later.
< ... Read more br />Disconnect the two wires and remove the two screws holding the metal plate. Same size nuts driver as the other screws.
Remove the sensor by just wiggling it out.
Slide the intake assemby out of it's spot.
Slide the new one in.
Then just do everything you did in reverse.
Takes 10 minutes. Super easy.
-
Eric from KILLEEN, TX
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers
Replaced with new water valve solenoid. Leak stopped. Yah!
-
Blair from EDMOND, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Socket set
-
William from LIVONIA, MI
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
-
Carl from BAREFOOT BAY, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
-
Danny from QUAKER CITY, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Socket set
-
Phillip from STANWOOD, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
1. Unplug the washer from the electrical outlet.
2. Turn off the water supply to the washer.
3. Disconnect the hoses directly at the back of the washer, remembering which one was on which side. You can also attach them to the new water inlet valve assembly at this time, as it can be installed with the hoses on.
4. Remove the two vertical screws at the back of the washer. They are on the far sides. Use a quarter inch bit to remove them. Keep them nearby.
5. You can now gently remove the control panel top by pulling up and toward the back of the machine. Be gentle so that you do not pull up any wires or dislodge any hoses!
6. You will see two electrical plugs attached to the inlet valves. Gently unplug them. One of them has a plastic tab holding it on, so pull that up carefully as you slide it off.
7. There is a small circular plug in the center of the blue inlet valve assembly. Gently remove it by prying it up from the metal circle. There is also a small rubber o-ring that should still be attached to that plug, but it might have come loose and still be in the water inlet valve contraption, so pull it out with something and stick it back on the plug with the circle metal piece.
8. Remove two small screws that are near each other that hold the blue inlet valve assembly in place. There is also a metal bracket holding it there that will come loose once these screws are removed.
9. You can now remove the entire blue plastic piece by rotating it and pulling through the hole.
10. Put the new water inlet valve in, and plug everything in the way it was, securely fastening screws and hoses. Be sure that no other hoses or wires came loose from the control panel.
11. Plug the washer back into the power, turn the water back on, and that should be it!
-
Elijah from Chesterton, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Socket set
Disconnect both water hoses from washing machine.
Remove two screws (one on each side) from upper silver colored metal plate on back of washer to allow access to (blue) water inlet valve.
Slightly lift the bottom portion of metal plate and slide to release hooks for ... Read more easy removal.
Pull back and tilt forward plastic control panel to get it out of your way.
Disconnect two electrical connections (one on each side) of water inlet valve. One of these came off easily but the other one was stubborn and I had to force it off with a screw driver. If there is an easier way I don't know what it is.
Remove two screws from water inlet valve. (one on each side)
Gently pull up on stainless steel water temperature sensor located in the middle of the water inlet control valve. It has a black wire connected to it so be careful.
Once you have disconnect the sensor you can remove the water inlet valve.
If you look closely you will see a small blue O-ring in the hole where you removed the water temp sensor from the water inlet valve.
The new valve DOES NOT come with a replacement O-ring so you
will have to re-use the old one. I used a small jeweler's screwdriver to get the old out of the hole.
Don't forget to install the O-ring or your washer WILL leak!
Put everything back together in reverse order.
Check hose connections for leaks.
Hope this helps somebody. Wish I had known about the O-ring. It would have saved me a headache.
-
George from CLARKSVILLE, TN
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
The people at PartsSelect were helpful in selecting the right part and the repair is working fine. My wife is happy.
-
Rock from HOUSTON, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set, Wrench set
1. Shutoff Water Valves
2. Removed hoses from Washer
3. Removed two screws to get control unit off.
4. Removed wires to valve assembly.
5. Removed Screw holding assembly in place.
6. Removed temp sensor from assembly.
7. Unit came right out and reversed the process for rep ... Read more lacement Unit.
8. Very easy...
-
Daniel from MILFORD, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
- < Prev
- 1
- 2
- Next >
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- 2
- Next >
10 people found this helpful.
5 people found this helpful.
5 people found this helpful.
3 people found this helpful.
2 people found this helpful.
2 people found this helpful.
1 person found this helpful.
1 person found this helpful.
- < Prev
- 1
- 2
- Next >
Manufacturer Part Number: WH13X26535
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.