Make sure you haven't got the discount earlier.
ROD & SPRING Assembly LEFT - WHITE WH16X26911
Rated by 4 customers
Really Easy
30 - 60 mins
Ratings submitted by customers like you who bought this part.
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
ROD & SPRING Assembly LEFT - WHITE Specifications
How Buying OEM Parts Can Save You Time and Money
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
-
Steve from Dexter, OR
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
-
Lawrence from FREDERICKSBRG, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
First checked lid switch. It turns out that the connector was disconnected. Probably became disconnected after the shaking from an unbalanced load. Reconnected and worked for three loads, then failed to spin again.
Purchased switch kit, belt and mode shifter, but held off the replacement. Parts select shared t ... Read more he diagnostic sheet. You can find yours inside the washer in a Ziploc bag. Tilt washer back and look underneath.
Went through diagnostic codes and all checked out fine. Did a fault reset. Worked again for three loads then failed to spin. GE sent a tech ($109 for service call). His diagnosis read-out showed rods/springs needed replacement. Parts arrived in three days and took about 45 minutes to r&r (I marked the new ones with a marker when unpacking to avoid confusion). USE VISE GRIPS AND.INSTALL FROM THE TOP. DO THE REAR.ONES FIRST Afterward, three loads done fourth load no spin.
Replaced lid switch with the kit. Again 3 loads fine, 4th load spin fail.
Note; each unplug & replug in resets the error codes, which may explain the 3 load temporary fix.
Did more research...
Finally, replaced old lid switch with lid switch kit (old switch was functioning fine, but I had the kit, so replaced it, in the event it was throwing an error code. Again 3 loads fine, 4th failed to spin.
Tilted washer back 45° for bottom access. Removed old belt. Belt and pulleys were loaded with grease/oil. Pulled both pulleys and scoured them. Replaced mode shifter. Note; old belt was about 3/4" larger diameter than new belt. Part#s matched, so it was the correct belt. Obviously the old belt was very worn. Oil/grease may be a combination of two things 1-slight leak from transmission seal, without any puddles on the floor and 2- the heat from the worn belt degrading the petroleum within.
While under the washer, removed the pump and hoses, checking for obstructions in the hoses and impeller. None found.
While underneath I grabbed the tech sheet from inside wall.
Checked the capacitance of the capacitor. Spec on the capacitor is 60 +/-5%. Mine tested at 61.1...within specs. (Be sure to discharge capacitor safely first!)
Reassembled the machine. Working fine through fifteen loads so far.
Final note. YouTube videos for all these steps online.
Conclusions; mechanically easy repair for DIYer. Probable causes...Belt worn, mode shifter and rods/springs worn out.
Total cost ~$200 parts + $109 for GE tech call.
Labor ~3 hours, but only because of so many disassembly re-assembly attempts at repair. Had it all been done at one time, total time would've been <1.5 hours
Thanks parts select and Barb (you're awesome)
-
Jan from POMPANO BEACH, FL
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
-
Donn from FREDERICKSBRG, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
- < Prev
- 1
- Next >
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
3 people found this helpful.
- < Prev
- 1
- Next >
Manufacturer Part Number: WH16X26911
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.