Make sure you haven't got the discount earlier.
Dual Burner Element with Limiter W10823694
Rated by 4 customers
A Bit Difficult
1- 2 hours
Ratings submitted by customers like you who bought this part.
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
1. Turned off the circuit breaker for the range. The range is hard-wired, so can't just be unplugged. I determined the clock on the range went off.
2. Removed 4 screws holding the front control panel to the cooktop. Removed 2 screws from each side panel into the cooktop. Removed 4 screws from the ... Read more rear panel holding the cooktop.
3. With my assistant (my wife) lifted the cooktop and tilted it so that I could access the underside.
4. Used an iPad to take photos from several angles of the wire connections from each burner control. Printed the one showing the connections on the dual burner control.
5. Removed the 4 screws holding the sheet metal support for the dual burner and one of the other burners. Released the spring steel retainers holding the dual burner. Removed the burner.
6. Used the iPad again to take photos of the connections to the dual burner, and printed it.
7. Removed all the wire connections to the burner. Checked continuity from the center (common) terminal to each of the other terminals. Determined that in fact the inside coil was open (burned out).
8. Removed the two screws holding the spring clip retainers on the old burner. Matched the old and new burners to determine where the spring clips should go. Drilled 2 small holes in the base of the new burner and screwed the clips from the old burner on the new one.
9. Now the tricky part: The new burner didn't have the exact same limiter and heat sensor probe as the old one. After several false starts, we were able to barely make out the terminal letter/number designations on the control and match them to the same letter/numbers on the new burner. It required a magnifier and a strong flashlight to read these engraved markings.
10. Made the connections on the burner. I used a pair of long-nosed pliers to carefully pull the connections off the spade terminals, and attch them on the new burner.
11. Mounted the burner to the sheet metal support using the spring clips previously installed.
12. Re-attached the 4 screws holding the burner support to the cooktop.
13. Carefully replaced the cooktop onto the range, paying special attention to not pinching any of the wires, and making sure all the wires, from all the burners were still connected.
14. Replaced all 12 screws holding the cooktop to the range.
15. Turned on the power, and checked all burners, including the new one, to see if they were opetating properly. YAY! They all worked!
It must be noted that we had to call a repairman to troubleshoot our installation the first time. We had reversed two of the wires to the new burner, because of the difference between the old and the new limiter connections. The engraved markings in the porcelain were very difficult to see. The instructions that came with the new burner never addressed this issue, and instead had very confusing (and worthless) instructions about replacing the limiter from the old burner to the new on. (This was not possible, anyway).
After the repairman left, we discovered the front burner that had been working, no longer was. With our newfound experience, we repeated the previous steps to take the range apart and discovered one of the wires had become disconnected from that burner. We re-connected it, re-attached the cooktop, and everything worked.
One telltale indicator that we had mixed up the connections on the burner, was the red "hot' warning light on the range top came on as soon as we restored power, even though no burners had been on. I should mention that the dual burner "worked" a couple of times even with the reversed connections, but then failed to work any more.
-
Art from CINCINNATI, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver
-
Qiong from Mckinney, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
-
Richard from Weatherford, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers
The heating element was broken, very hard to see.
Remove 2 clips and install in new element. Great oppurtunity to clean the unit.
-
Ashok from Los Altos Hills, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
- < Prev
- 1
- Next >
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
2 people found this helpful.
1 person found this helpful.
1 person found this helpful.
- < Prev
- 1
- Next >
Manufacturer Part Number: W10823694
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.