Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
SPRING CLUTCH WH01X24434
Fits your GTW335ASN0WW Washer!
Rated by 3 customers
Easy
30 - 60 mins
Ratings submitted by customers like you who bought this part.
$
8.56
In Stock
Get FREE EconoShip on orders over $100! T&C apply
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Fits your GTW335ASN0WW Washer!
PartSelect Number PS11763251
Manufacturer Part Number WH01X24434
Manufactured by
GE
Troubleshooting
This part fixes the following symptoms:
Noisy and Marks Left on Clothes | Spinning Issues | Will not agitate
This part works with the following products:
Washer.
This part works with the following products:
General Electric, Hotpoint.
Customer Repair Stories
Average Repair Rating: 3.5 / 5.0, 3 reviews.
What's this?
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
needed mode selector, and gears replaced
year and a half old unit.
The Mode selector failed to properly engage the gears and gears were grinding.
O moved dryer out of area. And then turned off water, disconnected the hoses from wall. Placed hoses including drain hose into 5-gallon bucket and clamped so they would stay. I then moved washer away from wall about 2'. The ... Read more n tipped it back against wall. Used 2x4 to keep it there as a support. (Doing this allowed me to keep it in the area and not dump water on floor. Then removed the gear guard, gears and mode selector. Reinstalled all parts and packed gears with synthetic grease made for plastic. It is now working like new. Parts were exact match. Took 30 minutes. Also cleaned the dryer vet line while I had it apart.
The Mode selector failed to properly engage the gears and gears were grinding.
O moved dryer out of area. And then turned off water, disconnected the hoses from wall. Placed hoses including drain hose into 5-gallon bucket and clamped so they would stay. I then moved washer away from wall about 2'. The ... Read more n tipped it back against wall. Used 2x4 to keep it there as a support. (Doing this allowed me to keep it in the area and not dump water on floor. Then removed the gear guard, gears and mode selector. Reinstalled all parts and packed gears with synthetic grease made for plastic. It is now working like new. Parts were exact match. Took 30 minutes. Also cleaned the dryer vet line while I had it apart.
Read less
Other Parts Used:
-
Scott from SHEBOYGAN FLS, WI
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Grinding noise when washing
I watch a YouTube video with the same problem and follow each step
Other Parts Used:
-
Selinda from BELLE GLADE, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Grinding noise LIke Gears that are not setting correctly.Disc
Disconnect power,turn off water,disconnect hose hot and cold. Disconnect drain hose careful water may drain out after you disconnect. Move washer to a place where you have enough room to work.Now lean washer to the floor on its back side Make sure to hold the lid from falling back I secure the lid with tape so it would not open. The washe
... Read more
r should on its back side , you should see a gray wheel with a nut.Remove nut and pull the gray wheel off. you feel a magnetic pull, Once removed, you will see 3 screws remove stator now remove all screws holding the speed senors remove Mode shifter hold the Clutch because the spring is under it. Once you start it easy to replace. install new parts.
Read less
Other Parts Used:
-
Jose E from Mission, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Socket set
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Back to Top
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Back to Top
You May Also Need
?
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11763251
Manufacturer Part Number: WH01X24434
Manufacturer Part Number: WH01X24434
Brand
Model Number
Description
Back to Top
SPRING CLUTCH
$
8.56
In Stock
✖
Stock Status
In Stock
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.