Make sure you haven't got the discount earlier.
Center Seal Retaining Washer WPY015666
Rated by 2 customers
Easy
More than 2 hours
Ratings submitted by customers like you who bought this part.
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Center Seal Retaining Washer Specifications
How Buying OEM Parts Can Save You Time and Money
- < Prev
- 1
- Next >
-
Tim from Diamond, MO
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
* Remeove two screws that allow the top to hing up.
* Loosen set screw on agitator (1/4" socket)
* Remove Agitator
*Loosen spanner nut from mounting seal with hammer and punch remember to loosen, turn clockwise
* Remove Inner Tub
* Losen Mounting stem with Hammer and Punch- Remember to l ... Read more oosen, turn clockwise
* Remove Boot seal with hands
* Remove bolts from the three brackets that attach to the outer tub
* Remove Outer Tub hoses
* Remove outer Tub. CAREFUL, I cut my hands on sheet metal when outer tub broke free and came up
* Knock Outer tub bearing out with large block of wood
* Cut bearing sleeve off of the transmission with a drimmel tool and cutting wheel. It was siezed on and would not turn off. Also, first tried to chisel , but was too difficult
* Cleaned area where bearing sleeve came off with fine sandpaper
* Put small amount of non-permanent thread lock on transmission (bearing area) before installing the new bearing sleeve because the sleeve is not pressed on and I did not want it to turn freely
* I did not but new bolts for the outer tub 3 brackets, but noticed that they needed to be sealed. So I bought some rubber washers at hardware store
* I also used some stuff called CLR to clean some rust off of the outside of the INNER tank
* I replaced the O-ring on the top of the agitator shaft
Also, on the agitator shaft: To really do it right, I probably should have changed the agitator shaft because the old seal wore grooves into the shaft. I took my chances and cleaned it up with some fine metal sandpaper. I could not get the worn grooves completely smooth, but did not want to take off more material as I thought it may cause a leak. We'll see
* I just used a hammer and punch to retighten the mounting stem and Spanner nut. REMEMBER COUNTER CLOCKWISE TO TIGHTEN
* This was not too bad if you are somewhat mechanically inclined. I could have got a new washer, but quite frankly, I get more satisfaction from seeing the old one keep working
* One last thing...and this is mostly for the younger guys cause the older guys already know it. CLEAN EVERYTHING on the washer...make it look like NEW and tell your wife how much you saved. Make sure you have the parts and tools to do the job within a timeframe that you do not have to go to the laundry mat and do not leave a big mess. This advice will definately pay off.
GOOD LUCK
-
Dan from Mason, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers, Socket set, Wrench set
- < Prev
- 1
- Next >
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Manufacturer Part Number: WPY015666
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.