Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
William T - March 8, 2020
Verified Purchase
Easy Repair
Part fit exactly as instructions stated. Quick service and very helpful assistance when ordering.
★★★★★
★★★★★
James D - June 18, 2019
Verified Purchase
Easy Repair, worked as expected
The part was in great condition. fast delivery. my washers works like new again.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Code F26 was displayed
I removed the rubber gasket, unscrewed the door latch, and removed from behind the gasket. It’s easily accessible from the front for removal and installation. However, it ran for two cycles normally, then displayed the code again.
Brigham from Throckmorton, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
6 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mike
July 23, 2019
This machine will not start.
For model number WFC7500VW2
Hello Mike, thank you for your question. The most common reason a unit that won't start is the latch. We would recommend testing the part to determine if it has failed, and if so it will need to be replaced. I hope this helps!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Gary Kidwell
January 15, 2019
Door locks but door lock light flashes and will not fill
For model number WFC7500VW2
Hi Gary,
Thank you for your question. According to the owner's manual for your washer, when the Door Locked LED light illuminates, the door is locked.
The door is locked and unlocked automatically, depending on the
stage of the wash cycle. Press and hold CANCEL/DRAIN for
3 seconds to unlock the door manually. It will take approximately
1 minute for the door to unlock. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Lisa
January 20, 2020
My washer is not going into a high spin. Should I replace the door lock assembly. Do you have the part number?
For model number WFC7500VW2
Hello Lisa, Thank you for the question. If the Tub is not spinning at all then we woudl suggest test Lid Lock. If the tub is spinning but not at the correct Speed, the Lid Lock is fine. This could be an issue with the Drive Motor, PartSelect Number PS11749959. We hope this helps.
The machine starts sporadically. Lights flash etc but it does not fill with water. Sometimes it takes 4-5 tries. Once it starts it works fine.
For model number MHWC7500YW
Hello John,
Thank you for your question. Our sources suggest replacing the electronic control board under part PS11749949 for your model to fix the washers issues. We hope this helps.
Washer does not always sense the door is closed. I have to push hard on the door, on area where the spring-sensor sits behind the door. Which part would you recommend needs replacing?
For model number WFC7500VW1
Hello Kevin, thank you for your inquiry! Our research indicates that the issue is probably with the Door Lock Assembly, part number PS11749964. If that is not the problem or if you have already fixed that, then the problem would be related to the Door Switch, part number PS11749963. Customer service is available 7 days a week if you need help placing an order. Glad to be of assistance!
Hello,
The error code F 13 comes on the display after performing a diagnostic test. Per manual it indicates a door lock/switch problem. It would lock at first when I close the door, then i hear a click and it proceeds to unlock OR before I would have to reopen the door and slam it for it to lock and fill. What do you suggest ?
For model number maytag washer mhwc7500yw0
Hello Rosie, thank you for contacting us. The f13 error code indicates a door lock failure. We would recommend replacing the door lock assembly, part number PS11749964, to fix the issue. It prevents the washer door from opening during the wash cycle or spin cycle. We hope this solves your problem!