Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
Single Front Panel Clip WP53-0120
Fits your CAV2004AKW Washer!
Rated by 1 customer
Easy
30 - 60 mins
Ratings submitted by customers like you who bought this part.
Fits your CAV2004AKW Washer!
PartSelect Number PS11742802
Manufacturer Part Number WP53-0120
Manufactured by
Whirlpool
Product Description
Single Front Panel Clip Specifications
This front panel clip is just about an inch long. It is green in color and is made of metal. This clip is intended for use with the front panels of washers and dryers.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Dryer, Washer.
This part works with the following products:
Norge, Magic Chef, Admiral, Maytag.
Part# WP53-0120 replaces these:
53-0120
Customer Repair Stories
Average Repair Rating: 3.3 / 5.0, 1 reviews.
What's this?
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
EXCESSIVE Banging, shaking and squeaking while on Spin Cycle
1)Start with empty washing machine.
2)Disconnect Hot, Cold, Power and Drain lines
3)Move machine to open area, open top by popping 2 front retaining clips.
4)Remove Front panel, remove small clear water level hose at lower rear of tub.
5)Remove small Rear access panel, disconnect large tub drain hose from pump and drai ... Read more n into small container, about 4 cups of water will come out.
5)Remove the 6 suspension Springs.
6)Place two large towels next to washer and tip machine onto its side slowly.
7)Remove drive belt from bottom, and slide out wash tub assembly thru top opening, be Careful not to damage large Plastic drive pulley on bottom of tub.
8)With tub upside-down, remove drive pully small plastic cover in center, remove E-Clip and remove pulley.
9)Slowly loosen snubber ring retaining bolts a few turns, DO NOT Remove, just loosen enough until snubber is free to move around.
10)Remove snubber ring by walking it around the retaining ring and install new snubber.
11) Clean machine cabinet and clean machine base where snubber touches with alcohol or Windex.
12) Reassemble in reverse order and Do Not Forget to reattach the small clear Water level sensing HOSE to the tub before closing the top.
13)Place Drive Belt onto the 2 small pulleys First, then slowly turn large pulley while walking belt onto it.
14)Reconnect machine to utilities and test run on small load to ensure no leaks and propper operation.
15)Enjoy Quiet free operation once again :)
2)Disconnect Hot, Cold, Power and Drain lines
3)Move machine to open area, open top by popping 2 front retaining clips.
4)Remove Front panel, remove small clear water level hose at lower rear of tub.
5)Remove small Rear access panel, disconnect large tub drain hose from pump and drai ... Read more n into small container, about 4 cups of water will come out.
5)Remove the 6 suspension Springs.
6)Place two large towels next to washer and tip machine onto its side slowly.
7)Remove drive belt from bottom, and slide out wash tub assembly thru top opening, be Careful not to damage large Plastic drive pulley on bottom of tub.
8)With tub upside-down, remove drive pully small plastic cover in center, remove E-Clip and remove pulley.
9)Slowly loosen snubber ring retaining bolts a few turns, DO NOT Remove, just loosen enough until snubber is free to move around.
10)Remove snubber ring by walking it around the retaining ring and install new snubber.
11) Clean machine cabinet and clean machine base where snubber touches with alcohol or Windex.
12) Reassemble in reverse order and Do Not Forget to reattach the small clear Water level sensing HOSE to the tub before closing the top.
13)Place Drive Belt onto the 2 small pulleys First, then slowly turn large pulley while walking belt onto it.
14)Reconnect machine to utilities and test run on small load to ensure no leaks and propper operation.
15)Enjoy Quiet free operation once again :)
Read less
Other Parts Used:
-
robert from simpsonville, SC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
127 of 137 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Back to Top
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Back to Top
You May Also Need
?
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11742802
Manufacturer Part Number: WP53-0120
Manufacturer Part Number: WP53-0120
Brand
Model Number
Description
Back to Top
Single Front Panel Clip
$
38.69
Special Order
✖
Stock Status
In Stock
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.