Make sure you haven't got the discount earlier.
Torsion Spring - Stainless Steel - Right Side WP4452396
Rated by 6 customers
A Bit Difficult
1- 2 hours
Ratings submitted by customers like you who bought this part.
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Torsion Spring - Stainless Steel - Right Side Specifications
How Buying OEM Parts Can Save You Time and Money
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
That said easy to install the two Torsion Springs.
-
Denis from SAN RAMON, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers
-
Mark from Franklin, TN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
glass and stainless steel panel (Hold on to the door handle
or the face and glass will come crashing to the floor; learned this after the first time a couple of years ago $$$). Set the stainless steel panel in a safe area until ready for reassembly.
Next, you must r ... Read more emove the black plastic cover which is still
remaining on the door in order to get to the springs. There are 2 screws that hold the plastic cover which are difficult
to access without removing the side and bottom trim of the
microwave opening. The spring was easy to replace at this point and didn't require any tools; just observe when taking
the broken one off, plus you can use the other spring as a
go by. Replace the black plastic cover, the bottom trim, the
side trims and the stainless door panel and it's complete!
-
Randall from Little Rock, AR
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1) Removing the two inside-door screws will completely release the fairly heavy exterior door panel from two holding clips at the bottom of the door unit. So BE PREPARED and HOLD THE DOOR HANDLE while removing t ... Read more he two screws or panel will crash to the floor. Fortunately I did. Consider help to hold and "catch" the exterior door panel.
2) The inside-door (which the exterior door is attached to) has a plastic frame that needs to be removed to gain access to the springs. However, removing the two screws holding the plastic frame located in the bottom-edge of the inside-door required removing stainless steel framing around the sides and bottom of the MW unit. This additional SS framing around my microwave/oven combo might be the result of a custom cabinet install.
3) Inserting the spring (torque tension rod) was a bit tricky using screw driver and needle nose plyers to hold and twist both ends into place. Again, a second set of hands might help. At this point, the door spring action feels too strong but when re-installed, the weight of the exterior door will normalize this.
4) Re-install plastic frame, SS cabinet framing if applicable, exterior door centered onto holding clips, and you should be finished. Check that two screws in step # 1 holding exterior door are tight without stripping to ensure your repair job doesn't result in the exterior door crashing to the floor following normal use.
5) In all, the spring cost $45 w/tax and 3-day delivery and the repair time was about 30 minutes vs. repair estimates starting at $129.
-
Michael from Austin, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
The replacement of the tension spring is easy. Getting there is the hard part. First, you need to remove the grill between the oven and microwave doors. There are ... Read more 2 screw in the center and one on each end. Then just pull it away from the oven. This allows access to the the two clips that hold the bottom of the door on.
Next, remove the 2 u-shaped clips on the bottom of the door on both sides. 1 screw each. The bottom of the door will be loose, so be careful on the next step.
Open the door. Clamping the outer part of the door and the inner part with one hand, remove the 2 screws on the the inside of the door cover. They are closest to you at 10 and 2 o'clock. The outer door trim will now come off. Put it aside and close the door. On the bottom of the door frame, locate and remove 2 more screws about 6 inches from the ends and the inside plastic cover will be free to remove.
Now you will be able to remove the broken tension spring by lifting and threading it out of the groove it sits in. Replace with the new tension spring by threading the looped side into that groove first and criss-crossing it over the other tension spring. Then locate the hole on the opposite hinge and slide it in place. This will lock it in. Reverse the procedure for putting the door back together as you did removing it. You may want to get someone to help you hold the door open considering the new spring will snap it shut without the weight of the door on it. After you reassemble the door, replace the vent grill between the doors and you're done.
-
Perry from Farmingdale, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
-
Lance from Angels Camp, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers
- < Prev
- 1
- Next >
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- 2
- Next >
13 people found this helpful.
2 people found this helpful.
1 person found this helpful.
1 person found this helpful.
1 person found this helpful.
- < Prev
- 1
- 2
- Next >
Manufacturer Part Number: WP4452396
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.