Make sure you haven't got the discount earlier.
V-Style Spin and Agitate Belt - 28-3/4 inches long WP27001006
Rated by 12 customers
A Bit Difficult
1- 2 hours
Ratings submitted by customers like you who bought this part.
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
V-Style Spin and Agitate Belt - 28-3/4 inches long Specifications
How Buying OEM Parts Can Save You Time and Money
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
- < Prev
- 1
- 2
- Next >
-
Elizabeth from Englewood, CO
-
Difficulty Level:Very Difficult
-
Total Repair Time:1- 2 hours
... Read more r />To replace the Idler Pulley Wheel:
1. Take off the lower and upper front panels to access the motor assembly.
2. Remove motor by loosening four bolts.
3. Remove spring that applies tension to the idler pulley.
4. Remove the electrical connector by squeezing the plastic tab on top.
5. Remove hoses by gripping clamps with pliers (put down rags first to catch water)
6. Unhook belt from tub pulley
7. Remove 1 cabinet spring to make it easier to remove motor
8. Remove motor.
9. Remove allen screws holding the pump to the motor
10. Remove the pump and belt (take note of the location of the belt before removing).
11. Remove retaining ring to replace Idler Pulley Wheel (this was probably the trickiest part; I used a very tiny needle nose pliers and straight screwdriver).
12. Replace the washers on either side of the Idler Pulley Wheel as well as the retaining ring.
13. Replace belt.
14. Reassemble in reverse order.
15. Be thankful for the money you saved on a service call.
-
Jim from Swanton, OH
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
A search ... Read more of the internet produced the order for drive belt, which arrived in a timely manner trough Fedex.
Replacing the belt was the most labor intensive part of the process. No mirror being available a CD was placed in the base of the machine in order to view what fasteners (Three torx head) fasened the pump to the motor assembly. Removal of the pump was necessary in order to replace the belt.
The removal of the fasteners required that three holes (120* angular spacing, 1/2" diameter, located on the pump fastener bosses) be drilled in the machine base in order to
remove and replace. This required setting the machine on its side. (Tell the engineers to put an inspection plate there in order to negate having to drill the holes. Thankx.) Pump assembly was lowered off driveshaft and belt replaced. Tensioner set on belt after pump assembly fit to driveshaft and torx fasteners replaced and tightened. Machine powered up, checked for function. In use. Lower cover replaced. I'll be using your buisness for parts again, no doubt.
-
Henry from Bradenton, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Wrench set
The outer tub should slide right off. Remove the bearing from the transmission. Supplies that you will most likely need are the 3m800 sealant, when you get this you will only need a little around the bottom of the lip where the new seal attaches to the bottom of the outer tub. You will also want to get the Seal tool which will ensure that the seal that goes around the top of the transmission spline is seated properly. Assemble in reverse order but keep in mind to attach tub bolts prior to attaching the springs. Also keep in mind that both maytag and amana make a washer with the same model number LWA80AW. Check to see which one you are ordering for. The kits are different. Don't ask me how I know. Just make sure you get the correct kit the first time, it will save you a whole lot of head scratching.
-
Tracy from martinez, GA
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
-
Kristine from Montgomery, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
2) removed water pump. Three small torque bit screws and (2) hoses.
3) removed motor (because I realized that the belt tensioner also needed work as it was siezed) removed (4) bolts and an electical connector.
4) repaired tensioner by taking apart and cleaning bearing surface. Ne ... Read more eded snap ring plyers to take apart.
5) put motor back in
6) replaced belt
7) put water pump back on
8) intalled front panels back on washer
-
TOM from MERIDEN, CT
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Socket set
I found a small ... Read more sock in the pump. Pump itself was still good (I think), but I installed new one along with new belt (just in case).
-
Artur from Burlington, CT
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set
-
Ralph from Moreno Valley, CA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
I then worked the belt off the aggitator pully and removed the hoses from the pump. I then used a 1/2 in soclet on long extension th remove the ... Read more four bolts that hold the motor and pump assembly. I then worked the assembly out of the cabinate and using a long #20 torx bit I removed the pumfrom the housing. I removed the belt, then I removed the housing off the motor and replaced the Idler bracket with the idler pully. I then re-assembled it in the reverse of taking it apart. Works great with the new idler and belt.
David Hilton
-
David from Raytown, MO
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Socket set
It works like a new one.
-
George W. from Thomasville, GA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
- < Prev
- 1
- 2
- Next >
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
2 people found this helpful.
- < Prev
- 1
- Next >
Manufacturer Part Number: WP27001006
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.