Make sure you haven't got the discount earlier.
Filter Gasket Assembly WD22X10043
Rated by 8 customers
Easy
15 - 30 mins
Ratings submitted by customers like you who bought this part.
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Filter Gasket Assembly Specifications
How Buying OEM Parts Can Save You Time and Money
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
-
Betty from Woolwine, VA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
-
Larry from Woodbridge, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
-
George from Sandy Hook, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
-
Harvey from Mount Clemens, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
removed palstic screen in back 4 screw
removed piston and nut assembly by unsrewing
reassemble
-
Randall from Coopersville, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1. Manually unscrewed the lower dishwasher sprayer from the base of the dishwasher. (The filter gasket cannot come out with this in the way.)
2. Using a nut driver, unscrewed the old plastic filter cage in the rear.
3. Thanks to a tip from another user on this site, I carefully pried up ... Read more the metal grommets on the two plastic studs in the front. I did this slowly with a flathead screwdriver, as I was worried about breaking the plastic. (Some plastic did whittle off of the studs from the sharpness of the grommets, but not so much that they were ruined.) Note, the studs look like something that can be replaced if you break them. They are not molded into the tub, as far as I can tell.
4. Removed the old (rotten looking gasket). Be careful! The edges around the filter drain are sharp. Used a turkey baster to suck out water from the filter area and wiped away mildew. The filter recess had broken glass in it and some other yucky stuff.
5. Easily reversed process with the new gasket. The new one has a lighter color and has the plastic, upside down basket thingy built-in. (No sharp edges). I pushed the metal grommets back onto the plastic studs, working them down as tightly as possible. They seem to be holding well.
Piston and Nut Assembly for Check Valve:
I wasn't sure I needed this, but ordered it anyway after seeing comments that the seal can corrode.
Mine looked ok, apart from food build-up, but I replaced it anyways.
1. Removed the screened housing that covers the length of the bottom-rear using nut driver.
2. Unscrewed the existing valve manually. It was easy to do. Cleaned area out as best as I could.
3. Reversed process with the new part.
-
John from Youngsville, NC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
The check valve was tota ... Read more lly worn out.You must turn the dishwasher back to it's in use position and open up the door.Inside the lower rear wall is a plastic cover with 4 screws remove these and the cover.Then unscrew the piston and nut assembly and remove the check valve.Simply replace with the new parts and reinstall the cover.
I replaced the gasket before I reinstalled the check valve even though it looked ok.To do this you need to turn the dishwasher over again and remove the 4 screws dolding the resevoir the check vave is in.Replace the old gasket with the new one and reinstall the new gasket.Do this after removing the old check valve and before intalling the new one.
On the bottom inside the dishwasher I noticed the large white gasket on the floor was falling apart so I replaced that also.I'm glad I did because below this assembly there is a reusable plastic filter that was totally plugged that I cleaned and reinstalled before relacing the filter gasket assembly.To do this you must remove the plastic water jet.With a screw driver there are 2 plastic tabs that must be carefully pulled out so you can pull out the water jet.Remove the 2 screws and plastic cover on top off the gasket assembly.Retain the 2 screws but you will not need the cover it is part of the new gasket assembly.There are two clips you need to carefully pry off.Then lift out the old gasket assembly and replace with the new one.Reinstall the 2 screws that held the old cover before and If reinstall the old clips if not damaged.You can purchase new ones but usually not needed.Then gently snap the water jet in place.
Put the dishwasher back under the counter and reconnect the power,water line and drain hose.
-
Mark from Sheboygan Falls, WI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
... Read more I also replaced the screen on the floor of the wash compartment because the rubber was deteriorating there too. Here I had to remove the spray arm by carefully prying the locking tabs outwards and lifting the entire spray assembly upwards. Then, then plastic covers need to be unscrewed and removed. The new part had the plastic cage molded into it. So I discarded the old plastic cage. There are a couple of retaining clips that are a little tricky to get off the plastic posts. But, they can be removed by prying a standard screw driver underneath and working them off the post. Do not break the plastic post, and save the retaining rings. The new part does not come with any screws or retainers, so you will need to re-use them. Simply, place the new screen in position, slide on the retaining clips, and screw down the cage. The spray assembly is just slid back onto the shaft and snaps into place. A lot of writing, but was rather simple to do. 15-20 minutes.
-
Daniel from South Elgin, IL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
- < Prev
- 1
- Next >
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
Manufacturer Part Number: WD22X10043
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.