Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Getting F 1 and 2 error codes and the oven turned itself off.
Really easy but in this model there are 2 versions of the sensor, male and female. The website didn't have any place to see that. So the first sensor that came was male but we needed the other. After calling they sent me a return form and sent the new part (which was actually much cheaper) overnight and it went in very quickly. Would check this out again when anything went wrong. they are great folks to work with.
Removed the two screws that hold the back glass in place. Rotated old bulb out of it's lamp fixture and replaced it with the new bulb. Replaced glass and reinstalled the screws. The hardest part was finding the bulb ... a very unique 18W flourescent. I wasted a couple of hours trying to locate it locally at my regular suppliers. The order at PatsSelect was easy and direct and the bulb was on my doorstep 3 days later .. an exact fit. Thanks guys.
I removed only 3 screws that allowed me to lift the glass top on the stove. I removed the burner and I could see where it short circuited. I ordered the new burner element. After it arrived I replaced it by moving the wires from the old element to the new element, and put it back together. I am sure that I saved at least $200 in "labor".
1. Slide the Oven door out of its hinges after removing the screws - see Owner's manual. 2. Place door on floor with the inside face on the floor. 3. Remove screws on side and bottom of door and the lift away the side stamped pieces. 4. Remove screws as they becom visible and lift away the pieces till you reach the inside glass.
Remember the sequence and be careful not to strip the Phillips screws when unscrewing.
first I unplugged the stove,took the screws out of the pan that holds the element to the stove, then unplugged the element.then I plugged in the new element, then screwed the screws into the pan that holds the element into the stove. it was very easy.
Regarding my right side oven door hinge replacement, P/N PS2172201
After reading that other people had trouble threading the screws into the new hinge, I looked at the drilled mounting holes in the new hinge. Neither hole was threaded. The smaller hole used a self tapping sheet metal screw which works fine. The larger hole gets a machine screw and will not self tap. Since the instructions say put the screw in "once" to tap the holes before installing the hinge, I tried this. It doesn't work, regardless of what the instructions say. The larger hole should come from the manufacture threaded. I do have a tap and die set so I tapped the hole myself. After that, the installation is a 5 min. ordeal.
Take the two screws, one on each side, out that hold the oven door on the hinges. The door will then pull straight off the hinges. Take the storage drawer below the oven out. Unscrew the top and bottom hinge screws and pull the old hinge out from inside at the bottom. Put the new "threaded" hinge into position and hold from the bottom, inside. Screw in the two screws, large one on the top end, and put the door back on. You can open both hinges about 30 degrees to allow the door to slide back on the hinges easily. Put the last two screws in that hold the door to the hinges and you are done.
Really very easy and saved several hundred dollars in repair bills. I might add that my hinge arrived on time 3 or 4 days after the order was placed.
Removed the door and old hinges and reinstalled the new hinges and added some screws to better support the door ( it was bending a little at the middle and the door would not shut all the way. Now it works fine.
TURNED OFF POWER TO STOVE Removed 5 Knobs, 2 screws that held bad switch. Removed 4 screws and lifted panel up and forward to expose switches. Adjusted spring tension on knob stem to hold knob ( stem in new switch slightly smaller) removed wire from defective switch one at a time and fastened to new switch in sequence. Reassembled and turned power on. Defective switch had stuck contacts making it full hot.
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
left side hinge was broken. I removed 2 screws to release the old hinge and replaced it with the new hinge. Part select.com made it easy to pick out the part from the diagram supplied on the web site. After it was ordered it arrived 2 days later.
Old hinge snapped a rivet. It could no longer hold the weight of the door.
I removed the two screws and pryed out the old hinge. I then put in the new hinge. The new one fit well. I went to screw it in with the supplied screws. The screws not only did not fit the hole tapped in the hinge (too big, different tread) but both screws were different from each other. They were different sizes and different types all together. I tried re-using the screws from the originol hinge but they also did not fit. I then got my own self tapping machine screws and finished the job. This job should not have been that hard. If they had supplied the correct screws, It would have taken all of five minutes.
I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just 4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .