This 40w light bulb is a replacement bulb constructed of glass and metal. It is an easy-to-install electrical part which produces 40w of light. If the bulb won't light up then it may be broken and sho...
$8.87
In Stock
Order within the next 11 hrs and your part ships today!
This Charcoal Filter traps grease from your oven's exhaust to help prevent it from entering the vent, which could cause damage over time. If the exhaust fan on your microwave is not working, you may n...
$11.52
In Stock
Order within the next 11 hrs and your part ships today!
This Grease Filter is constructed of Acrylonitrile Butadiene Styrene and is used to trap grease and help eliminate odors from the exhaust air while cooking. It attaches onto the exhaust and is rated ...
$35.41
In Stock
Order within the next 11 hrs and your part ships today!
This mounting plate is sourced directly from the original manufacturer for use with microwaves. It is a metal plate designed to support a microwave by attaching the microwave to the wall studs. If the...
$15.83
In Stock
Order within the next 11 hrs and your part ships today!
This diode, or high voltage diode, is used in microwaves. It is an electrical current control device that ensures power flows in one direction and not the other way. If your microwave produces no heat...
$29.50
In Stock
Order within the next 11 hrs and your part ships today!
If your microwave is not turning on it could be due to your fuse needing to be replaced. This part protects the microwave by shutting it off if there is an electrical surge. This fuse is just over an ...
$24.71
In Stock
Order within the next 11 hrs and your part ships today!
The light socket in your microwave houses the light bulb and connects it to the power source. The light bulb will screw into it, so the light bulb will be held in place. Be very careful when installin...
$11.13
In Stock
Order within the next 11 hrs and your part ships today!
This glass tray drive coupling, also known as a tray support, is a genuine OEM replacement part. It can help solve the issue of your microwave tray not turning properly. This motor couple connects the...
$9.93
In Stock
Order within the next 11 hrs and your part ships today!
This damper is an authentic OEM replacement assembly used in microwave/range hood combos. It includes the damper door and frame. It is designed to direct the flow of air through the vent duct, and the...
$73.03
In Stock
Order within the next 11 hrs and your part ships today!
This is a manufacturer-approved mounting kit for your microwave. This kit is crucial for keeping your microwave securely wall-mounted. This kit does not include the mounting plate itself. This kit com...
$62.51
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for WMH53521HZ1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Judi
April 6, 2023
Error code on screen F1E4, MW power relay. What does this mean? How do I fix it?
For model number WMH53521HZ1
Hello Judi, thank you for your inquiry. The error code F1E4 shows there is a problem with the microwave control board. We recommend you replace the control board, part number PS12348884, to resolve the issue. We hope this solves your problem!
microwae starts up for 5 seconds then shuts off???
For model number WMH53521HZ1
Hi Dan, thank you for reaching out to PartSelect. If the microwave runs for a few seconds and then shuts off, the door switch might be defective or loose. Sometimes arching or overheating of door switches stops the microwave from running efficiently. Check door interlock switch & holder assembly, part number PS12349017, to fix your issue. Good luck with this repair!
When I replaced the hood light for this microwave it stays on all the time and heats up - do I just have to replace part on control board?
For model number WMH53521HZ1
Hello Richard, thank you for reaching out. Based on the description that you have provided, we would recommend replacing the control board, part number PS12348634, to fix the issue. We hope that helps!
Does not recognize that the door is closed gives message "Open/Close door"
This problem is intermittent leading me to suspect one of the micro switches.
What do you think?
For model number WMH53521HZ1
Hi Allan, thank you for contacting us. This symptom indicates that the door switch is defective. We suggest that you replace the door interlock switch and holder assembly, part number PS12349017. If you require assistance to place an order, please contact customer service. We hope that helps!
The nightmare was that this microwave is installed under the cabinet....in order to get to the light bulb I had to pull out my stove then squeeze into the space between the stove and counter....my old microwave light bult was much easier to change.....Shame on Whirlpool for making this so difficult.....must be a better way to cover the li
... Read moreght bulb so that we do not need a screwdriver to remove the door to get to the light bulb
Unless you have a very comfortable background with electronics and electricity, I don't necessarily recommend taking apart a microwave. If you are very handy and are going to be VERY cautious to follow the rules of discharging caps and testing voltages before moving forward, then go for it. That said, I took the microwave off and apart.
... Read more Not knowing where to find the parts, I was fortunate that the installer put the instruction book for the microwave inside the front vent slot above the touchpad for reference. it details the location of every part and it tells you very clearly what each part you test should show specific to this microwave on your multimeter. Find this guide online if you don't have it. Turn on the microwave for 20 seconds with a glass of water to make sure it's not heating - that with the noise means it's eeither the magnetron, cap, or diode. Read the notes on this site for all of the basic things to look for with the magnetron, diode, and capacitor. Once comfortable with the guide, locations of those devices, and how to test, then take it down and apart. Unfortunately, I didn't do all those things in that order, and it only wasted a lot of time trying to find the parts. Once I found the parts and put all the screws and covers back for all the areas that didn't need to be accessed for the repair, testing went quickly. The diode was bad. Ordered a new one and had it in 3 days or so. That means your microwave will be apart and sitting somewhere for a little while until you get the part and have time to repair it. Putting the diode back isn't too bad. Reassemble the microwave and put it back up again. If i had to do it again, it would take me 20 to 30 minutes once the microwave was down and on a table. Also, I used some bricks with towels over them or you could use some sawhorses to keep the microwave elevated so you can plug it in and run it after installing the new component. Again, make sure you discharge the cap before touching anything again even if you didn't run it, but just plugged it in.
