This manufacturer-certified drip bowl is also known as a drip pan, and it is designed for use with cooktops and ranges. It sits below 8-inch burner elements and catches drips and spills from the cookw...
This drip bowl is used for electric cooktops and ranges, it is designed to sit under a 6-inch surface burner. It catches the drips and spills coming from the cookware on the surface burner. This drip ...
This bake element is located at the bottom of the oven to supply heat and it has push-on terminals. If your baking element is burnt out, the heat is not consistent, or is defective, then replacing the...
This oven temperature sensor, for ranges, works together with the oven control board to measure and regulate the oven temperature. The sensor detects the temperature in the oven cavity. If the followi...
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
This part is for oven ranges, it connects individual wires and protects the device from electrical surges, voltages, and current. With this part, the house power is connected to the range wire harness...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
This switch controls the stovetop surface burner.
This surface element control switch is for ranges.
Surface element control switch turns the surface element on and off and controls how much hea...
This is cookware designed for use in your range or oven. It is a two-piece dish that is used to grill or cook food while the broil function is on, meaning it can withstand high temperatures. This set ...
This broil element supplies heat for cooking purposes and is located in the roof of an oven. If you find there is little to no heat when cooking, a burned-out element, or food is taking too long to co...
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Roberto
April 6, 2023
Please please help me to find those 4 burners for mi stove Whirlpool (model: WFC150MLAB0).
Thank you, very much.
For model number WFC150MLAB0
Hi Roberto, thank you for the question. The left front and the right rear elements are the 8-inch surface element, part number PS12347890, each. The right front and the left rear elements are the 6-inch surface element, part number PS12348067, each. They are sold individually. Therefore you may need to order two of both elements. We hope this helps!
Tested the temp sensor 1074 ohms at room temp. Range will not keep a set temp. What else could be the problem?
For model number WFC150MLAB0
Hi Greg, thank you for your question. There are a few parts that could cause this issue in your appliance. First I would say test your elements with a multi meter to see if they are working correctly or not. They should be reading between 0 - 50 ohms to be working correctly. The other part you should check would be your oven temperature sensor. That can also be tested with a multi meter and should be reading between 1000 - 1100 ohms. You have already checked that and it is within the working range. If those three parts are fine however, then the issue may be in your control board. Good luck with your repair.
Was this helpful?
Thank you for voting!
Greg
January 30, 2020
Oven will not stay with thermostat setting. I have tested the elements and temp probe, all are within range. What else could it be ?
For model number WFC150MLAB0
Hi Greg,
Thank you for your question. If you have tested the elements and the temperature probe, you will need to check the electronic control board. We hope this helps. Thank you and have a great day.