Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 4 at 11:59pm EST.
Models
>
WED8300SW0
WED8300SW0 Whirlpool Dryer - Overview
Sections of the WED8300SW0
[Viewing 4 of 4]Manuals & Care Guides for WED8300SW0
Click to downloadKeep searches simple, eg. "belt" or "pump".
Dryer Thermal Fuse
PartSelect #: PS11741460
Manufacturer #: WP3392519
The Dryer Thermal Fuse (Thermal Cutoff, Temperature Fuse) is a 2 by ½ inch, white, plastic safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. If the fuse ...
$19.61
In Stock
Door Catch Kit
PartSelect #: PS334230
Manufacturer #: 279570
This part replaces your appliances latch (Door Latch Kit, Door Catch, Dryer Door Latch Kit). On your appliance you will find both a strike and a catch. The strike is mounted on the body of the dryer, ...
$5.04
In Stock
Lint Filter
PartSelect #: PS1491676
Manufacturer #: W10120998
The filter collects lint during the drying cycle. This filter is 12 1/2 inches wide and 10 1/2 inches deep. Replacing the lint filter is an easy repair which requires no tools. When replacing the lint...
$61.41
In Stock
Idler Pulley
PartSelect #: PS334244
Manufacturer #: 279640
This Idler Pulley includes the tri-ring and gasket and everything included here is manufacturer-certified. This part maintains correct tension on the drive belt in order to spin the drum properly. If ...
$26.92
In Stock
Dryer Repair Kit
PartSelect #: PS373088
Manufacturer #: 4392067
This dryer repair kit consists of five commonly replaced dryer parts: one multi-rib belt (part #661570V and measures 93 1/2 inches long), four drum support rollers, one idler assembly, nine tri-rings,...
$53.54
In Stock
Dryer Drum Support Roller
PartSelect #: PS11752609
Manufacturer #: WPW10314173
This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. The part includes the d...
$22.67
In Stock
Multi Rib Belt
PartSelect #: PS382430
Manufacturer #: 661570
The Drive Belt is a 93 1/2" belt which wraps around the dryer drum to allow tension and movement. If broken the dryer will not turn properly, or there may be loud noises. The part is rated as "medium"...
$21.93
In Stock
Thermostat, Internal-Bias
PartSelect #: PS11746740
Manufacturer #: WP8577274
The internal-bias thermistor (Thermistor, Dryer Thermister, Dryer Thermistor) prevents the dryer from overheating by monitoring and controlling the temperature of the inside of the dryer drum. It is l...
$47.70
In Stock
Roller Support Tri-Ring
PartSelect #: PS11755850
Manufacturer #: WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
$13.41
In Stock
Leveling Foot
PartSelect #: PS1609293
Manufacturer #: 49621
If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so...
$11.37
In Stock
Idler Pulley with Bracket
PartSelect #: PS11726337
Manufacturer #: W10837240
The idler pulley wheel is now sold with this arm. This idler pulley is for dryers.
Idler pulley maintains correct tension on the drive belt to spin the drum.
$26.76
In Stock
High Limit Thermostat and Thermal Cut-Off Kit
PartSelect #: PS334387
Manufacturer #: 279973
Also known as Thermal Cut-Off kit. The thermostat acts as a safety mechanism that keeps the dryer from overheating and the fuse is like a backup system - it's set to trip at a higher temperature than...
$53.23
In Stock
Questions And Answers for WED8300SW0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- 2
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Roger Hunt
March 26, 2020
Will not come on. Sensing light, light come on
For model number WED8300SW0
Hello Roger, thank you for writing. Here is a link to what parts to check and how to check them when this issue occurs. Here is the link: https://www.partselect.com/Repair/Dryer/Will-Not-Start/ . I hope this helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Chrystine
January 9, 2020
Hello, My Whirlpool duet sport washer gives error code 5d during the rinse cycle and will not continue. It also will leak water out of the front.
For model number WED8300SW0
Hello Chrystine, Thank you for the question. I think the code is a SD. This could be caused by using too much detergent or not using High Efficiency (HE) detergent. The washer will not be able to spin out water with the excess suds. When "Sud" or "Sd" is displayed, the washer automatically extends the rinse time to remove the excess suds. If it still will not run, you may need to remove the hoses and pump to clean them from any suds build up. we hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Mary
February 2, 2020
Whirlpool duet front load washer will not spin fast
For model number WED8300SW0
Hello Mary, thank you for writing. If there is an issue with the unit spinning, you may have a defective Belt. We advise checking that part in your model for any damage. I hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Billy
November 29, 2022
I need a new dryer top and your parts list has two listed. I believe One is no longer available,I think part # PS1175311 which is still available,is the one I need. could you referance the serial number to check? ser. # MU1550866.Thank You.
For model number WED8300SW0
Hello Billy, thank you for reaching out. The dryer top compatible with your given model is part number PS11753111. If you require assistance to place an order, please contact customer service. We hope that helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Linda
September 14, 2023
I need lint filter for my whirlpool duet sport dryer.
For model number WED8300SW0
Hello Linda, thank you for getting in touch. The lint filter for your model is part number PS1491676. Glad to be of assistance!
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- 2
- Next >
Common Symptoms of the WED8300SW0
[Viewing 12 of 12]Noisy
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Not Heating
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Door Pops Open
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Heat stays on after drum has stopped
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer was working, but no heat.
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of ... Read more needle nose pliers, it was held in place by two screws, once they were removed the fuse came out easily, I checked continuity with a volt meter placing the meter on X1 Ohms and could not get a reading.
I replaced with a new one and put it all back together the way I took it apart.
Then I plugged it in and it worked first time, I now have warm dry clothes.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of ... Read more needle nose pliers, it was held in place by two screws, once they were removed the fuse came out easily, I checked continuity with a volt meter placing the meter on X1 Ohms and could not get a reading.
I replaced with a new one and put it all back together the way I took it apart.
Then I plugged it in and it worked first time, I now have warm dry clothes.
Read less
Parts Used:
-
ANTHONY from CHESHIRE, CT
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
2973 of 3350 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat but would run otherwise
Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.
Ascertaining the problem was the most time consuming part.
The actual repair was quite simple and did ... Read more n't take but 15-20 minutes.
Ascertaining the problem was the most time consuming part.
The actual repair was quite simple and did ... Read more n't take but 15-20 minutes.
Read less
Parts Used:
-
Dana from Grassvally, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers
878 of 952 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Catch part had fallen out,/ was missing
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source.
Parts Used:
-
Terri from Saint Augustine, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
672 of 732 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!