Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
seal was black and stiff from burned in spilled grease and sauce
Unscrewed and pulled the door off and then took the three layers of the door apart in order to clean off the burned-on goop and remove the old and insert the new seal. The last screw was rusted in and the drill stripped it so that it was impossible to remove. I levered the remaining two layers apart, holding them open with screw drivers, and inserted the new seal. Had to be careful with the shaping of the metal core of the seal and the distribution of the sealing fabric. Phew! I saved the screws from each layer separately by taping them to the counter in the order of removal. This made reassembly easier. Getting the door back on was a bit difficult and I needed another pair of hands to help me.
1.remove the trim around the door (8 screws) 2.remove over glass panel (part with the handle) Caution; the springs on the door are exactly set for the weight of the door. When we removed the outer glass panel, I almost killed my wife when the door slammed shut. 3.Remove inner metal cover (6-8 screws).some of these screws were baked pretty tight so I used vise grips on their little heads to convince them to get turning. 4. To get the door window out you must also remove the inner enamel baked cover, held on by 5-6 screws from the back. This is also the pieces which holds the door seal in place, so it is a good time to change that as well. 5. After cleaning up all the broken glass from the old window, the new window slides right in - perfect fit! Reverse the steps to put it all back together.
From the time the glass broke until it was completely repaired took only six days! Pretty amazing for a twenty year old oven.
Older model oven with model number worn off. Photo with the 1" grid made it possible for me to find the right size part.
You only need a phillips head screwdriver to install this seal, but it is a bit tricky to line up the new seal and the fiberglass insulation inside the door, so take your time and make sure everything lines up and is tucked in before tightening the screws. Probably easier to do with 2 people (especially getting the door back on the spring loaded hinges) but I was able to do it solo without too much difficulty.
After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.
I dissasembled the entire door..lots of screws and watch you dont drop the glass pieces...also keep them in order so you dont get confused on what goes where. I cleaned everything nicely and installed the new seal and everything went together perfectly and looks and works like new. I recieved my part by mail very quickly and the price was MUCH better than my local repair shop.
I removed three screws, pulled the element out from the rear wall, unplugged the electrical connections, reversed these steps in installing the new element. "A Piece Of Cake!"
Oven door latch was bent and did not release or lock
Had to disassemble the top of the stove and the control panel on the front. I took digital pictures as I disassembled so I could refer to them when putting the stove back together, especially when disconnecting wiring. It took about 3 hours, but most of that time was spent thoroughly cleaning 16 years of baked on grease from places that are normally unaccessible. The new latch works great - the wife is happy!
temperature probe insulation broken down so short circuit
As the probe is a plug-in item that would normally be out of the oven, there was nothing more to the repair than checking that the new probe plug fitted the socket and that it was detected by the oven. Then the old probe was consigned to the trash.
Everything checked out, and the probe was used satisfactorily within a couple of days.
Inside Glass of Oven Door broke and needed replacement.
Serviceman took out broken glass by removing door and separating front of door from back of door. He carefully removed all broken glass Then replaced with new glass and fastened door together . He did repair in 20 minutes. Oven is like new. Thank you very much for still stocking this part that allows me to keep my oven repaired.
Opened the oven door and locked the spring hinges in the opened position with two 10p nails. Removed the oven door. I dismantled the component parts of the door. I then removed and replaced the broken glass unit,reassembled the door, slid the door onto the hinges, tightened two screws to lock the door in place, removed the 10p nails, closed the door----- and that was it. Less than one hour. The job was accomplished using only a Phillips screwdriver.
Interior window dirty (sealed unit; unable to clean)
Using exploded view and previous customers' comments, I disassembled the door. It was primarily a matter of finding all the screws. I recommend taking the door off first (I didn't), but watch your fingers. The hinges have very, very strong springs and you can hurt your or your helper's fingers if you're not prepared. The hardest part was keeping all the insulation in place while your're installing the assembly. I also replaced the gasket. That takes four hands, two to hold the gasket in place and two to reinstall the window assembly. To put the door back on the hinges, I pulled them out from the door at a 45-degree angle (takes some effort), put screwdrivers through holes in the hinges, and guided (with help) the door back on.
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
First I removed the four torx screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I installed the new element in reverse order. Recycled the cardboard box and the old element.