This gasket wraps around the sides and top of the dishwasher door and helps seal the door when it is closed to prevent water from leaking from the dishwasher during the washing cycle. If your dishwash...
The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element...
The dishwasher lid spring helps open the dispenser cover in the soap box when the control releases the latch. If your dishwasher does not dispense detergent, is broken and worn out, or the door is not...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of wat...
This cap does not require the use of an O-ring seal. The wet agent assembly cap is clear in color and made of plastic. This is a part for your dishwasher. This part may need to be replaced if you noti...
The lid hinge pin or detergent lid pin on your dishwasher helps dispense your dish detergent when your dishwasher is running. The pin fits with the dispenser lid and allows the lid to pop open and dis...
This soap cup latch kit, used in a dishwasher, will keep the dispenser cover closed. If your dishwasher will not dispense detergent, there is a door latch failure, the dishes are not cleaning properly...
Installed new door seal. Dishwasher still leaked. Googled the model number and then cleaned the filter at the bottom of the dishwasher, still leaked. Verified that manifold bearing was not work. It was OK. Found note that a plugged vent might cause leaking door. Very counterintuitive. Pried off air vent cover. Vent was tho
... Read moreuroughly plugged with calcium deposts from steam. Cleaned these out. Dishwasher no longer leaks.
The first thing I did was to investigate. I needed to find where the leak was coming from. It was leaking from just above tne door front panel, directly underneath the control panel buttons. I opened the dishwasher door, and decided to remove the door screen vent. I was covered with some offwhite fiberous, or filter like material. I thou
... Read moreght perhaps the filter had broken down, and I ordered a new screen. When it arrived, and, although I had expected to receive a new filter with the plastic door screen, I didn't. There wasn't one to be ordered. I looked at the screen again. My problem was, that although I had considered that the substance I had thought was a filter, was instead build up of detergent, and other particals. That idea didn't seem to make sense. I didn't think it was possible for that stuff to get to the door screen. I thought, it was too far away from the dispenser and food particles. As it turned out, the buildup was, in fact, the problem. I properly cleaned the door vent, which was then fine, and I put it back into the door. There were no more leaks, that was it, and the problem was solved. As a last note however, unfortunatley, I have to return the new door vent screen that I ordered. I enjoyed solving the problem, and you all helped alot. Let's do it again sometime.
First, examine very carefully how the old spring relates to the detergent release box lid. Note that the top of the spring has a square-end upside down "U" . This rests on a small ledge on the detergent box. Also note that on either end of the spring is a straight extension of the spring wire. These two "legs" must rest on the inside o
... Read moref the edge of the detergent box. Second, use a flat blade screw driver to pry the LID hinge pin from the mounting "posts. Remove the pin, first noting the position of the spring. Reassemble the spring on the hinge pin in reverse order. Then snap the lid onto the spring using the two mounting "posts". NOTE: I used a very fine needle nose pliers to move the two spring "legs" behind the detergent box edge after I had mounted the lid. Flip the lid down to test if the spring pressure on the lid can be felt. Harold Kitzmann, Fishersville VA