Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
The compression nut is used as a connection between the water supply line and other components in your refrigerator such as your ice maker and your water dispenser. Tools required for this repair incl...
$13.15
In Stock
Order within the next 7 hrs and your part ships today!
This single outlet water valve is intended for use with some commercial ice machines, and not refrigerator icemakers. It comes with a mounting bracket, two screws, and a washer.
This is a plastic tubing insert kit for a refrigerator ice maker. This kit includes a package of four tubing inserts. The kit does not include other parts such as the ice maker water fill tube kit or ...
$11.12
In Stock
Order within the next 7 hrs and your part ships today!
This ice maker scoop is an OEM refrigerator part designed to retrieve ice from the ice maker bin. It is made of plastic and measures approximately 10 3/4 inches in length and 4 inches in width. The sc...
$11.83
In Stock
Order within the next 7 hrs and your part ships today!
Silicone rubber adhesive is a high temperature adhesive that is used for gaskets on dryers and felt seals. It is used on many different appliances for many different application reasons. This silicone...
$52.06
In Stock
Order within the next 7 hrs and your part ships today!
I removed the cutter grid and unplugged the light bulb and wire heating plug ins. I slid the front cover plate off the cutting grid and loosened the screws on the front of the cutter grid and unthreaded the broken, top grid wire, leaving the bottom wire in place as it was in tact. I then threaded the new wire through the cutting gri
... Read mored frame starting in the center and threading right and then left. While the threading was not difficult, the wire was easily kinked. The process up to this point was only 15 minutes or so.
Once it was completely threaded, I worked for a couple of hours trying to smooth and straighten the wire so that is was somewhat taut and straight enough to create symetrical ice cubes. My frustration came in pulling on the wire from the center point to each outside ending point where it was to be wrapped around the screw and the screw tightened back down. The wire was fragile enough that it would break, by the time I was finished I barely had enough wire left to touch the screw let alone hook around the screw. After 3 or four days of successful opperation, the grid quit cutting again. As I took it apart, it was obvious that the weight of the ice was enough to pull the wire, that was already too short, away from the screw. I refastened it again, but think it is unlikely to hold. If it won't hold, I would be hard pressed to purchase another wire. I may bite the bullet and purchase the entire grid mechanism with the wires already installed. Even though the cost of the entire grid mechanism is $200 more than the purchase of another wire, it may well be worth the ease of installation!
I removed the three nuts that hold the old pump, easy. Next step was to replace with the new pump, tricky, because it goes real deep in the machine and my arms barely reach it. After several attemtps, I finally reached one screw and bolt it immediately. Rest was piece of cake. What I liked most, is that you don't need to do any
... Read more wiring connections, because it uses a simple plug-in connector that goes in at the same time when you bolt the new pump. What it surprised me, was that my machine it's over 20 years old, and the new replacement water pump it's the very same design !!! Last night I fixed it, and today I'm enjoying again fresh ice. One plus for PartSelect : I inherit this machine and didn't have an Installation & Operation Manual,and PartSelect have it On-Line, so I printed it, and I believe I'm ready another 20 year period of fresh ice! Thanks a lot PartSelect !!!
This is a stand alone ice maker that uses a standard water valve. When the valve fails (usually stuck open) the water never chills enough to freeze because water is constantly flowing into the hopper. The valve is in the very front. Remove the front panel. Turn of the water supply and disconnect the valve. Replace the valve and turn on th
... Read moree water. Let the machine run through 1 cycle before the new valve will dispense water. Done.