Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 4 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The rollers on the upper rack broke
There are eight guides that hold the rack rails in place. Use a Phillips screwdriver to remove the top two guides on each side in order to remove the rack from the dishwasher. The plastic axles on the rack and the rollers snap on. Use the hammer and punch to bend the metal clip on one end of the rail. Remove the plastic end piece then slide the rollers out. Place two new rollers in the rail and put the plastic end piece on. Use the hammer and punch to bend the metal clip back into place. Snap the rails on the rack and set the rack on the guides in the dishwasher. Replace the top guide using the screwdriver, you will have to twist the rails in order get them in between the guides.
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.
Open the tiny plastic package in inserted the wheel onto the "axle". Opened the dishwasher, pulled out the bottom rack and snapped the wheel onto the rack. Done!
The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama.
The stud assembly in the middle of each wheel no longer stayed inside the wheel.
Just pulled off the old wheel. I just had to push in the stud to the wheel and pushed it on to the rack of the dishwasher. Very easy repair! Only disappointing part was that it bothered me to have to purchase the stud with the wheel. I was told they only came as the set. I only needed to purchase that inside stud. My wheels were fine.
1. I removed the plastic stops from the ends of the upper rack slides. 2. Removed the upper rack. 3. Unclipped the old rollers from the rack. 4. Clipped the new rollers onto the rack. 5. Made a grunting noise so the wife could hear. 6. Walked away
I removed the four screws holding the screen and molded plastic cage inside the rear of the dishwasher to expose the check valve assembly. I then unscrewed the piston and nut assembly with my hand and replaced it with the new one. I found that the rubber cone shaped valve on the old piston and nut assembly was entirely disintegrated. This easy repair solved the problem.
Washing machine would cease functioning at the spin cycle and would not drain.
Remove the front coverfrom the machine. This is done by removing the 3 screws at the bottom of the panel. The panel then drops down and pulls straight off. The pump is located on the front right wall of the of the machine. You will notice a 2-3 inch diamete threaded cap on the right side of the front wall of the machine. This is the front of the pump and access to the filter. Place a large bucket under this cap and slowly loosen the cap. All of the water remaining in the machine will begin to drain (this could be a lot of water. Do not remove the cap completely so that you can quickly stop the flow of water if needed). Once all water is drained from the appliance, Disconnect the two hoses from the pump using a pair of pliers to looses the presure clamps, sliding the clamps back an then pulling off the hoses (be careful of any remaining water in the hoses). Then remove the two screws from the rear base of the pump that secure it to the bottom floor panel of the washer. Slide the pump slightly to the rear to free it from the fittings on the front wall of the machine and the lift the pump up. At this point, firmly pull out the wiring harness plugged into the top right side of the pump. Install the new pump by plugging in the wiring harness and resecuring the pump. Plug in the machine and run on the rinse and spin cycle to test.
lower rack took one min. take out old slide in new
upper rack a little tricky had to remove end caps on rack arms to slide rack out to replace rollers. end caps are not snapped in they have a lever in the track that is part of the cap if you twist it a little cap will slide off. total time for this part 15 min.
Found a forum on the internet that said the Air Check Valve located under the screen on the bottom of the back wall inside the wash compartment may be the culprit. Took it out by using nut driver to remove screen, and twisting the part out. The seal was deteriorated. Repleacing the part was simply the opposite, and very easy.
I also replaced the screen on the floor of the wash compartment because the rubber was deteriorating there too. Here I had to remove the spray arm by carefully prying the locking tabs outwards and lifting the entire spray assembly upwards. Then, then plastic covers need to be unscrewed and removed. The new part had the plastic cage molded into it. So I discarded the old plastic cage. There are a couple of retaining clips that are a little tricky to get off the plastic posts. But, they can be removed by prying a standard screw driver underneath and working them off the post. Do not break the plastic post, and save the retaining rings. The new part does not come with any screws or retainers, so you will need to re-use them. Simply, place the new screen in position, slide on the retaining clips, and screw down the cage. The spray assembly is just slid back onto the shaft and snaps into place. A lot of writing, but was rather simple to do. 15-20 minutes.