Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element...
$7.77
In Stock
Order within the next 7 hrs and your part ships today!
This dishwasher drain and wash impeller kit comes with both the drain and wash impeller, gaskets, chopper, and installation screw. This part helps stop your dishwasher from leaking and helps with the ...
$109.38
In Stock
Order within the next 7 hrs and your part ships today!
The dishwasher lid spring helps open the dispenser cover in the soap box when the control releases the latch. If your dishwasher does not dispense detergent, is broken and worn out, or the door is not...
$7.97
In Stock
Order within the next 7 hrs and your part ships today!
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.80
In Stock
Order within the next 7 hrs and your part ships today!
Each tandem roller holds two wheels. There are four sets of tandem rollers in this roller kit, so you will be getting eight wheels in all. They are all white, and are meant for use on the lower rack of your dishwasher.
$29.22
In Stock
Order within the next 7 hrs and your part ships today!
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.02
In Stock
Order within the next 7 hrs and your part ships today!
Disconnect unit and remove from under counter. remove lower spray arm, tip over dishwasher on it's back, diconnect wires from motor , unscrew drain fitting rotate motor mounts to and lift pump and motor assembly up and out from inside the dishwasher. thoughly clean all parts during pump disassembly( under running water and a toothbrush
... Read moreworks well) . Looking at a parts diagram,and using your memory from disassembly replace the new seals and put it all back together, with patience you can do anything and use common sense.
Ordered both drain & wash impeller kit and the drain check valve with o-ring. Decided to test the cheaper drain check valve first. Pulled dishwasher out from wall & adjacent cabinetry; removed drain hose from disposer and drained as much water as possible; "jacked" side of dishwasher to gain access to drain hose and drain check valve; us
... Read moreed pliers to remove hose clamp; placed flat pan underneath to catch remaining water drainage; unscrewed drain check valve; tested under bathroom faucet--determined faulty; replaced with the new one, restored connections, reset dishwasher in proper location; voila--fixed! Plan to return the unneeded impeller kit.
Grinding Noise when running. I was not sure of problem and thought that a new Dishwasher may be needed if motor was the problem. After taking the bottom rack and spray arms out I came across my first problem. I believe it was the impeller design that has a 1in hex nut with a bolt in middle that needed to be removed. I needed a 90 degree 1
... Read morein wrench to hold impleller while I removed Bolt. Luckly I have a friend that is a mechinist who made me a wrench. After that the grinding cause was discovered - Broken glass that grinded the cermic shaft that is over motor shaft. I did not small drops of water under motor during grinding due to damaged cermic shaft. $24 and 2 days later my dishwasher is as good as new. Sugguest you sell a 1in 90 degree hard plastic wrench for holding impeller which bolt is removed. Thanks PS. - Best part of your site is Parts detail which was very helpful for me to understand assembly.