The drum roller for your dryer holds the drum in place while the drum turns on the support wheels. The drum roller is round with a bearing in the middle and measures approximately 3 inches in diameter...
The lint filter sits in your dryer, and collects loose lint when the machine is operating. Sometimes the lint filter will become clogged or damaged, and in this case, you will need to replace your cur...
$35.48
In Stock
Order within the next 1 hr and 37 mins and your part ships today!
This thermal fuse acts as a high-limit thermostat, and shuts off the heating element when the dryer overheats by cutting off power to the dryer. If the thermal fuse has blown, the dryer will not start...
$24.22
In Stock
Order within the next 1 hr and 37 mins and your part ships today!
This is an authentic dryer lint filter cover sourced directly from the manufacturer. It protects the more delicate lint filter in your dryer, so that it doesn’t get damaged and lint can’t mix in with ...
$44.24
In Stock
Order within the next 1 hr and 37 mins and your part ships today!
The sensor controls the temperature in your dryer and will turn off once your clothes have reached the desired dryness level. If you notice that your dryer is not giving off enough heat to dry the clo...
$22.26
In Stock
Order within the next 1 hr and 37 mins and your part ships today!
The belt wraps the length of the dryer drum, secured by a tension pulley and then loops around the motor pulley. If you find that the drum is not turning properly or at all while your dryer is in succ...
$31.24
In Stock
Order within the next 1 hr and 37 mins and your part ships today!
This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes...
The thermostat is a part for your dryer, and it is roughly 1 inch long by roughly 1.5 inches wide. The purpose of the thermostat is to measure the temperature of the air inside your dryer drum. As the...
$45.88
In Stock
Order within the next 1 hr and 37 mins and your part ships today!
This is a replacement lint screen guide for your dryer. The lint screen guide attaches to the front bulkhead and supports the lint screen. If your lint screen will not stay in place, or if you are not...
$42.72
In Stock
Order within the next 1 hr and 37 mins and your part ships today!
This is a thermostat for various models of LG dryers. This thermostat specifically is the rear high limit thermostat, and it is designed as a safety device to shut off power to your dryer if the inter...
$51.92
In Stock
Order within the next 1 hr and 37 mins and your part ships today!
This part is the replacement lint filter cover for your dryer. It is made of gray plastic and is approximately 11-1/2 inches by 1-1/4 inches. The lint filter cover fits on top of the lint filter and p...
$21.37
In Stock
Order within the next 1 hr and 37 mins and your part ships today!
Order within the next 1 hr and 37 mins and your part ships today!
Questions And Answers for DLE4970W
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ted
May 25, 2022
The front seal on tub tore and is in a knot i can't find part number for front gasket
For model number DLE4970W
Hi Ted,
Thank you for your question. The part number listed under your model number for the gasket is PS3535212. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
The dryer doesn't stop tumbling after the clothes are dried and cooled down unless i open the door, even pushing the off button doesn't stop it. Everything functions normal except it will not stop tumbling. What part do i need to fix it, thanks
For model number DLE4970W
Hello Ahmad, Thank you for your inquiry. We would recommend checking the following parts to fix your issue: door switch, door lock, or the main control board as it could be a stuck relay. We would also recommend checking your wiring for any visible damage. Hope this helps.
Dryer is not heating up. Only blowing air. What could be the root cause? What can i look for in the machine?
For model number DLE4970W
Hello, Thank you for your question. You will want to check the heating element- PartSelect Number PS3527791. We hope this helps, good luck with this repair.
Was this helpful?
Thank you for voting!
Ed
March 29, 2024
Can this model be swapped to a 3 prong cable?
For model number DLE4970W
Electric dryers require cords suitable for 240-volt, 30-amp circuits. Check to see if you need a 3-prong vs. 4-prong dryer cord. 3-prong plugs are used for homes built before the year 2000. 4-prong plugs are used for homes built after the year 2000. We hope this helps
Had to replace front drum support rollers. Removed screws underneath top in back that held bracket that keeps top in place. Slid top towards rear and lifted up. Removed 4 screws that hold plastic front panel in place (inside..2 on each corner) Unplugged front panel electric plugs to remove panel. Opened door..removed 2 screws at bottom of
... Read more door opening. Removed screws on top of front panel. Unplugged door switch plug. Removed front panel. Removed right front roller with 9/16th wrench for nut. Adjustable for back of stud. Lifted up on drum to get roller out. Reversed to install. Left roller a bit harder to get to stud. Removed and installed same as right side. Did not attempt to replace rear rollers. Have them if needed but very much more involved to replace.
I actually went to mr fix it on u tube. Great instruction on how to take dryer apart. First I unplugged the dryer. I found I could reach the heating system by removing the lint tube in the back of the dryer. I put my I phone with the light on inside the back of the dryer and tested the connections to see if all were working. The thermal f
... Read moreuse was not working. I removed the two wires , red on top and white on the bottom. Then used a small Phillips screwdriver to remove the two mounting screws and removed the fuse. I then used a vacuum to clear any lint from the back of the dryer and inside the dryer. This took me about an hour and a half. I did it this way because I did not want to disassemble the entire dryer to get to the components. I received the fuse in 3 days and tested it. It was fine. I then put it in the dryer screwed it in place, connected the wires. Replaced the lint tube. This took about 10 minutes. Dryer is running great.
Found disassembly video and watched several times. Suspected that one of the drum wheels had seized up. Found extreme volume of lint and hair inside unit as well as a dryer sheet melted on top of heating unit. Front left drum wheel was worn down from lint and hair jamming its movement. Video made it easy, not a really complicated piec
... Read moree of machinery. Replaced all 4 wheels due to normal wear on other three. Wanted to be sure drum evenly balanced on all 4. Parts came quickly and were easy to install. My sister and I did this together. Would not recommend doing it alone. Took time to vac and wipe down entire unit. Now it runs so quiet we have to look to see if it is operating. Got a brand new machine out of it, saved a couple of hundred dollars in repair bills, and found 11 cents inside the machine. For your own piece of mind, if you have had your dryer for several years, you need to open it up and clean it out. Its not hard... added note, we are both in our 60's... so if we can do it so can you.... Such a feeling of accomplishment, can't buy that in a store....
