Models > CDT835SSJ0SS > Symptoms > Not drying dishes properly

Parts That Fix General Electric Dishwasher CDT835SSJ0SS Not drying dishes properly

Not drying dishes properly is a commonly reported symptom for the CDT835SSJ0SS General Electric Dishwasher, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your CDT835SSJ0SS General Electric Dishwasher that will fix Not drying dishes properly. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!

1 HEATING ELEMENT
Fixes Symptom 90% of time
★★★★★
★★★★★
26 Reviews

Rated by 11 customers 

  

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.   

The element heating assembly is found at the bottom of the dishwasher tub, and helps to warm the water in the wash cycle, and dry the dishes afterward. If the water does not heat up during the wash cycle, or the dishes are not being dried properly, you may need to replace the element heating assembly in your dishwasher. This element heating assembly is horseshoe-shaped and is sold individually. To replace your heating assembly, first make sure it has cooled down, then simply slide the connecting tabs out. Replace with a new heating element and your problem should be solved.

$ 56.21
  In Stock
PartSelect Number PS16729156
Manufacturer Part Number WD05X30818

Customer Repair Stories

Dish washer not heating water not drying dishes.

Parts Select has excellent video instruction. they are way better than I could describe. the repair went smoothly. the heating element wasn't the issue. and it's may not be yours either. I found that the flood switch was the problem part number PS8690623. It's located under the filter screen in the bottom Yes that long grey plastic thing under the screen. It's held in by two 1/4 inch screws. Use a wet dry vacuum or towels to dry up the water in the sump. ABOVE ALL don't drop the screws. You'll be taking the pump apart if you do. Gently lift out the flood switch. There will be wires plugged into the base. With a flat screwdriver gently pop off the white plug from the green base. The plug only goes on one way reassemble in reverse order.
Read less
  • Richard from SPRING HILL, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench set
11 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Dry cycle was not working and dishes weren't getting dry.

Unplugged the dishwasher and turned off the water. In order to pull the dishwasher out I had to remove disconnect the waterline. Opened the dishwasher door to remove the screws attached under the counter holding the dishwasher in place. Once removed I pulled the dishwasher out of the under counter pocket far enough that I could access the rear connections to the heating element. Carefully disconnected the wires connected to the heating element and then loosened the large nuts securing the heating element. Once the nuts were removed I disengaged the element from the holders and removed it from the dishwasher. Installed the new element in place engaging it into the holders inside the dishwasher. Then moved back to the rear of the dishwasher installing the nuts that were removed earlier on the new element and reconnected the cables.

I ordered my new heating element prior to checking the continuity of the old one. I checked the continuity of the old one once it was removed and it was ok, not great but still acceptable so I knew the new element wasn't going to fix the issue, but installed it anyways. My issue was actually the float switch, so if you want to be sure of your issue, remove the current heating element from your dishwasher and check the continuity before ordering if you want to save some money.
Read less
  • Heath from PARKER, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
12 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2 SWITCH, FLOOD
Fixes Symptom 7% of time
★★★★★
★★★★★
1 Review

Rated by 2 customers 

  

Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.   

$ 8.06
  In Stock
PartSelect Number PS12068856
Manufacturer Part Number WD21X23498

Customer Repair Stories

Dishes not drying and no heat other than hot tap water

Pulled dishwasher out switch is on very bottom of pump housing, turned dishwasher on its back, took out 1/4" bolt holding on bottom of switch frame, took two very small screwdrivers and small picks to hold open switch clips, while switch was removed checked float for frew movement, put in new switch, removed screw drivers and picks checked to see all locked on new switch in position, replaced bottom plate and bolt, checked burner reset all good now dishwasher heats and drys!
Read less
  • Rick from FAIRVIEW, OK
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
3 STEM FLOOD
Fixes Symptom 3% of time

$ 88.70
  In Stock
PartSelect Number PS11771983
Manufacturer Part Number WD21X22838
Back to Top