Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer leaking
Opened the front panel with 3 crews T-25 or socket wrench. Panel comes off right away.
Look for the leak. Determined it was the hose. Use power pliers to remove the clamp.
The small clamp was easy. The big one I had to use my yoga to get to it. It probably would had been easy from the back panel but moving the machine requires brute force.
Once the hose was out I found some bra under wires which is what probably punctured the hose.
Removed the front filter and found a bunch of nails.
Assembly was much easier and placed clamps so that if needed it would be a lot easier to remove and replace.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
First some background. The door locked up the first time when appliance was less than one year old. The "Maytag Repairman" finally succeeded in getting the door open after propping up the front of the machine and fumbling around underneath for a period of time and then assured me the problem was solved. The problem recurred less than a year later, and I called another repairman who seemed to have an easier time of it, and charged $293.42 to replace the water level switch. About six months later the same problem recurred and I took the cover off the top of the machine and found there a booklet "For Service Technician's Use Only". VERY HELPFUL. Told how extremely easy it was to unlock door - took about five seconds. Replacing the switch itself involved pulling one tubing off and disconnecting one elec connection from old switch and replacing on new switch. Total cost $50 plus a few dollars for shipping.
looked repair on you tube followed instructions. took off broken latch. compared to pictures on sites. ordered part. part arrived in 2 days. put part on. suggest using first method quick and easy.
Using the Torx Screwdriver, we removed the door from the unit. Then we removed all of the screws on the inside of the washer door. After that we flipped it over and opened it up exposing the inside. We couldn't separate them entirely because there was a screw under the latch piece that we couldn't figure out how to get to. However with all the screws out on the inside of the door, we did have enough room to open it up and access the place cover that holds the hinges in. Once we accessed that we removed the roller tips from the old unit and placed them on the new one. Then we reversed the process. With a couple screws in we realized we had put the hinge in reversed from what it needed to be, so we reopened it and switched it around. Then completed replacing all the screws and reattached it to the washer. It opens and closes perfectly and we saved a couple hundred dollars for sure, as the quote to come out had been a $150 trip charge.
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Followed the video on the website. Very easy to replace the part and it fixed the problem. The trickiest part was reinstalling the ring that holds the rubber gasket in place.
So I was unable to get my model number so I took the hinge off the washer and was able to order the part. Before removing the hinge I used a marker and marked the hinge location on the washer. Once I got the part I removed the T15 screws on the inside part of the door and separate the pieces. I was able to remove the white tube for all 4 of the pins and put them on the hinge. I installed the hinge an then i put the front door pieces back together again while it was laying on the floor. I though I put it in wrong but I was correct. Once i had the hinge on the door and the door reassembled, I was able to attached the hinge to the washer. The hinge comes off the washer by pushing up on it and to reinstall you push down. I tighten the 4 T25 screws using the marks on the washer and the door is alligned correctly. I am able to close the washer door with one finger instead of my whole hand.
Desarme la puerta y coloque la nueva con mucha facilidad, nunca reparé un electrodoméstico antes de este, seguí el diagrama que encontré en el sitio para elegir la pieza que se rompio
Replacing the heat sensor following an F-24 Error Notice.
I followed your repair video explicitly, simple fix. However, one should be careful when disconnecting the two prong electrical connector from the heat sensor. the two black wires can pull free easily. In that case, the rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe the orientation slots on both the male andfemale connectors - they connect one way only! I set the washer on it's face while effecting this repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!