Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
light on to order water filter
Pressed in the end of the filter cover, lowered it down part way. Twisted the old filter 1/4 turn and removed it. Set in the sink to drain. Inserted new filter and twisted it to lock. closed cover. Done. Total time @ 1 Minute.
Removed the fruit & veggie drawers & the deli (pantry) drawer. Took out the 3 screws, removed the attached parts, put them on the replacement part, reattached it and put the drawers back in.
Here's the part I want to share: PartSelect had a expanded diagram showing the correct part and sufficiently detailed to figure out the repair before the part arrived. That's why I ordered from them. Secondly, I ordered the part Thursday morning--and the thing was sitting on my porch when I came back in from my evening out Saturday--2 days later!!!
Dropped a jug and broke the lower drawer hinge pin
Remove food off of lower shelf, remove the two produce drawers, remove large lower drawer, remove glass shelf, remove three screws holding end cap in place. Once end cap was removed the drawer track could be removed and placed on new end cap. Installation of new end cap took less than 5 minutes. Most of the time spent was removing/replacing food and cleaning the shelf/bins. PartSelect was awesome BTW!
Removing the existing filter by rotating as directed and then dislodging from 'docking' station proved difficult. Turns out, the old filter is under a bit of vacuum pressure and getting the unit to separate or release was a challenge.
I removed the drop-down outer housing by gently prying the sides of the two pivot pins at the rear. This gave me move 'room' to grip and slightly rotate then pull the old filter forward and away from the tight suction connection. I was concerned that I would be too forceful for the plastic assemblies and would break something; deliberate motions and a steady thought process on the problem helped disengage the darned old filter!
Remove Crisper drawers from Bottom Shelf. Remove glass from the top of Bottom Shelf. Drop new Crisper frame center rail into slots on the top of the Bottom Shelf shelf. Replace glass onto the top of the Bottom Shelf. Slide drawers between left and right guides and the Crisper frame center rail.
Total repair time less than one minute. No tools required.
I unscrewed the old one and replaced it with the new one. The real benefit was I got the exact part I needed w/o a 30 minute drive and sales people that ignored me. I had gone to the local store the day before and come home with the wrong part because i could not get assistance and the part # I had did not match what was labled on the package. I used the same part # on the website and got exactly what was needed, less that 48 hrs after I ordered it. thanks for the prompt service. we will be a repeat customer
Refrigerator sat in storage in sub zero weather, water in Dual Water Inlet Valve froze, cracking valve.
This is the 2nd time I have used PartSelect, and this experience was as pleasant as the 1st. The exploded-view diagrams make parts identification very easy; and the photo of the actual part is such a great idea, it allows you to verify what you need. I also got my part (cross country, in 3 days)
Repair Procedure: Shut off water supply. It may be easier to work if you disconnect the water supply tube, but it is not required. On the backside of the refrigerator, remove the bottom, black plastic protection panel. You will need a nut driver or battery-powered screw driver with a 3/8" socket tip on it. Next, remove the black metal panel that holds the water inlet valve in place. Remove screws with a nut driver. 1st remove the two flat-pin power connectors. (They are different sizes and color-coded, so there is no room for making a re-hookup mistake). Then proceed to remove the hoses. The hoses are pressure-lock tubing, so push the plastic disk in or down where the tube goes into the main body of the valve. Do this for all three hoses (tubes). Switch water valves and reverse the procedure. **Be certain that the tubes are pushed back in as far as they can go; if you do not re-seat the tubes, the pressure from the water going back in the valve, will blow the tubes right out the valve (ask me how I know this!). Once reassembled, turn the water back on slowly. Make sure you turn the water supply valve all the way open, it seats itself internally when you do and is less prone to drip leaks. That's it! (As a former kitchen remodeler, I find this a great DIY project).
1. remove deli draw 2. remove glass top & end caps 3. remove screws on side of end cap 4. remove end cap 5. remove crisper control connection bars & rear ductwork 6. reinstall crisper control connection bars & rear ductwork 7. install new end cap & rear ductwork 8. install glass top & end caps 9. install deli draw & cover
I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.
The easiest thing to do was pull the ice make off. After taking the 3 screws out of the wall of the freezer, take a screwdriver (flathead) and push on the tab for the electrical plug and wiggle the cord out. Then you can take 3 screws out for the main cover and another 2 screws on the next cover. There's the part, pop it out and replace holding pins and start the process of putting back together the opposite way you took it apart.
Well the frist thing I did was get out the all the paper work and look under trouble shooting.This frig has a list of codes to try to help narrow down what parts might be bad.Well at frist it seemed it was a Defrost Thermastat?Well thanks to PartSelect it showed me right where it was and step by step how to remove and replace it.It took me over 2Hr's,after that I let the frig run all night and the next morning(yep warm frig)not the part I needed,well now Im mad,the local part store said you need a 3in1 jump starter easy to in stall at $50.Can'nt bring parts back no way weather thier opened or not.So get home and can'nt see how this jumper is going to wire up to my compresser?So on to the Web site to get some info,find out that this part gets a thumb's down,it puts out more volt's then needed and kills your compresser the reviews where very help full.So back to PartSelect to see more info,then I spoted the Overload/Relay and went to the back of my Frig and this part just plugs right into the compresser,I pulled it of with pliers and Bingo a burn spot melted right through the Overload/Relay.Ordered the right part the same as the old one.Put the part in and Bam,compresser fired right up.If I only did alittle more home work I could off saved alot of head ach and money.Thanks PartSelect I'll alway's click on to your web site for future parts and advise.
removed ice maker and wire shelf. removed back panel screws and tilted forward. removed 2 screws holding motor bracket. swapped fan blade and reassembled
the upper half of the refrigerator wasn't being cooled
I called the repairman and he troubleshot the problem and told me that he could order the part or that I could. He quickly explained what to do. I ordered the part it came in with 2 days during that time I looked up on how to remove and replace the part on the website. The website stated it took around 15 minutes. That is all it took. I had to use a screw driver to remove two screws and seperate the connection. I reconnected the wiring per instructions on the website reversed the process and it was done within 15 minutes. I save a lot of money and time away from work. This is a grest site to get what you need to fix your appliances. If I have any problems with my other equipment I will becoming back to this website to get the parts and information
I want to thank you for providing the information and helping folks out that can do the job