Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
Kenmore Washer Dryer Combo Elements and Burners
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
![Kenmore Appliance Parts](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/images/brands/250/kenmore.png)
Popular Kenmore Washer Dryer Combo Elements and Burners
Your Price
$94.82
In Stock
Kenmore Washer Dryer Combo Dryer Heating Element
PartSelect Number PS11741416
Manufacturer Part Number WP3387747
When connected to electricity the dryer heating element glows red hot and generates heat. When air is blown over it, it heats the air which is used to dry the clothes. The heating element fits inside the heater housing inside the dryer. Wear and tear on the heater coil from use will eventually cause the coil to break and the element to fail. When this part fails it can cease to produce any heat. Alternately, the coil could break and short to ground allowing the dryer to continue to heat even when turned off. The latter is a fire hazard and the dryer should be disconnected from power until the element is replaced. If the element coil breaks, the element needs to be replaced. This model is 11 by 5 inches with 5/16” terminals, metal and ceramic, and comes in black. It is sold individually.
Fixes these symptoms
- Not Heating
- Too hot
- See more...
Installation Instructions
Alan from Brooksville, FL
Burned out heater element
Remove the kick plate from the bottom of the dryer by sliding a putty knife along the top edge to release the plastic clamps, one on each side about 4" in from the edges. The kick plate folds out and down. You will see the heat shield on the right, held in by one hex head screw. Remove screw and heat shield. The element is positioned in an open-front housing and is fastened to the left side of the housing by two hex head screws, located on the "rail" of the element and right near the two wires. Remove the hex-head screws that hold the element in place and disconnected the two wires by pulling them out by hand or with needle nose pliers. The only difficulty here is the cramped working area...I recommend a stubby socket driver for these two screws. Most of this I had to do by feel because I could not see the screw heads. Once the screws are out and the wires have been disconnected, slide the old element straight out toward you. You may need to disconnect a small plastic hose located to the left front of the element, but this hose just pulls right off. Vacume the dust & lint build-up out of the whole area, wipe out the element housing and clean up the whole underside of the dryer prior to installing the new element. Installation is reverse of removal. It also might be a good opportunity to clean out your exhaust duct and the vent to the outside. (Never use the aluminum foil-accordian-type duct.) If the exterior dryer vent has any kind of screen over it, remove it and get rid of it. Screens collect lint, lint builds up and burns out elements.
Read more...
Your Price
$11.08
In Stock
Kenmore Washer Dryer Combo Heating Element Connection Wire Kit
PartSelect Number PS334206
Manufacturer Part Number 279457
This kit is used for electric clothes dryers, and it comes with a yellow wire nut.
Fixes these symptoms
- Not Heating
- See more...
Installation Instructions
Christopher from dublin, OH
no heat
took a couple differant parts to fix the dryer. i ordered one part at a time. i was expecting to wait the 5 days for shipping but i got home from work the next day of odering parts and they were there waiting for me on my doorstep. all three times i ordered. this website is the best site to order parts. i wont go to another website or store if i need to order parts for appliances. u guys have my business for life. thumbs up.
Read more...
Kenmore Washer Dryer Combo Heater Coil with 5/16 Inch Terminals
While greasing the bearing in the back of the drum, I found my heating coil was broken. Steps to replace:
1) Unplug the unit
2) Remove the top panel. Note, do not remove the center front screw that does not go into the door.
3) Remove front outer panel
4) Remove interior front panel
5) Remove front control panel 6 screws, pushing downward the panel and disconnecting connection to door.
6) Remove door by removing the screws on the top and pull door straight off. (I left the air duct attached to the door)
7) Remove the back access panel to the motor
8) Release the belt from the idler pulley and remove the belt.
9) I removed the three screws in the center of the drum as I found it difficult to remove the drum from the bearing. Remove the drum.
10) disconnect the coil terminals by first bending the tabs outward to allow you to be able to pull them off the block
11) remove the old coil
12) carefully stretch the new coil so that it measures 48 inches (no more)
13) Plug new coil into terminals and bend tabs to lock in place.
14) Divide heater coil in half and install coil onto center support on the opposite side from where it connects to the block/back wall of dryer
15) Install remaining coils onto supports.
16) reinstall all parts in reverse order. Read more...
PartSelect Number PS451032
Manufacturer Part Number 5300622034
Coil only.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Mark from Normalville, PA
Dryer would not heat
First..kudos to PartSelect for their fantastic support! Great work folks.While greasing the bearing in the back of the drum, I found my heating coil was broken. Steps to replace:
1) Unplug the unit
2) Remove the top panel. Note, do not remove the center front screw that does not go into the door.
3) Remove front outer panel
4) Remove interior front panel
5) Remove front control panel 6 screws, pushing downward the panel and disconnecting connection to door.
6) Remove door by removing the screws on the top and pull door straight off. (I left the air duct attached to the door)
7) Remove the back access panel to the motor
8) Release the belt from the idler pulley and remove the belt.
9) I removed the three screws in the center of the drum as I found it difficult to remove the drum from the bearing. Remove the drum.
10) disconnect the coil terminals by first bending the tabs outward to allow you to be able to pull them off the block
11) remove the old coil
12) carefully stretch the new coil so that it measures 48 inches (no more)
13) Plug new coil into terminals and bend tabs to lock in place.
14) Divide heater coil in half and install coil onto center support on the opposite side from where it connects to the block/back wall of dryer
15) Install remaining coils onto supports.
16) reinstall all parts in reverse order. Read more...
Kenmore Washer Dryer Combo Heater Assembly
PartSelect Number PS2378363
Manufacturer Part Number 131475320
This dryer heating assembly has 5/16" terminal on the housing.
Installation Instructions
CAROLE from MONTICELLO, AR
Dryer still turned, but would not heat
Had to remove tub to get to rear wall to make the repair and then put it back together in reverse order.
Read more...
Kenmore Washer Dryer Combo Heating Element with Housing
PartSelect Number PS5574028
Manufacturer Part Number 137392700
Kenmore Washer Dryer Combo Heating Element
PartSelect Number PS11741418
Manufacturer Part Number WP3387749
This part is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is used to dry the clothes in your dryer.
Installation Instructions
Kevin from Mount Morris, MI
No heat
Wife completed the element and thermal cutoff installation while I was at work. The leads to the cutoff were removed, the screws removed the new parts were screwed in and the wires reconnected. The hardest part was putting the face back on the dryer. Partselect was a great source of information and the delivery was fast. Dryer works great.
Read more...
Kenmore Washer Dryer Combo Heating Element - 3000W 240V
PartSelect Number PS11740608
Manufacturer Part Number WP279843
This element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is used to dry the clothes in your dryer.
Installation Instructions
Roger from Hialeah, FL
Dryer running but not heating
Popped open rear access panel and logged on to website. Performed search for "dryer not heating" and came across helpful tips and ordered all components pertaining to heating system and removed and replaced them. Working better than better and saved myself hundreds of dollars. Highly recommend for those "do it yourselfers"!
Read more...
Kenmore Washer Dryer Combo Heating Element Coil Kit
PartSelect Number PS449327
Manufacturer Part Number 3937010
This kit includes the heating element restring coil, 2 insulators and a terminal block.
Kenmore Washer Dryer Combo Heating Element
PartSelect Number PS11741666
Manufacturer Part Number WP3403591
This element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is used to dry the clothes in your dryer.
Kenmore Washer Dryer Combo Heating Element Kit
PartSelect Number PS334215
Manufacturer Part Number 279506
Installation Instructions
Robin from Cedareadge, CO
Not heating
installed according to directions, went well. However I recommend getting a newer dryer, it is 15 years old and didn't work all that well, even when fixed.
Read more...
Related Kenmore Washer Dryer Combo Parts
- All Kenmore Washer Dryer Combo parts
- Kenmore Washer Dryer Combo Agitators
- Kenmore Washer Dryer Combo Bearings
- Kenmore Washer Dryer Combo Belts
- Kenmore Washer Dryer Combo Brackets and Flanges
- Kenmore Washer Dryer Combo Caps and Lids
- Kenmore Washer Dryer Combo Circuit Boards and Touch Pads
- Kenmore Washer Dryer Combo Drums and Tubs
- Kenmore Washer Dryer Combo Filters
- Kenmore Washer Dryer Combo Fuses
- Kenmore Washer Dryer Combo Handles
- Kenmore Washer Dryer Combo Hardware
- Kenmore Washer Dryer Combo Hinges
- Kenmore Washer Dryer Combo Hoses and Tubes
- Kenmore Washer Dryer Combo Knobs
- Kenmore Washer Dryer Combo Latches
- Kenmore Washer Dryer Combo Motors
- Kenmore Washer Dryer Combo Panels
- Kenmore Washer Dryer Combo Seals and Gaskets
- Kenmore Washer Dryer Combo Springs and Shock Absorbers
- Kenmore Washer Dryer Combo Switches
- Kenmore Washer Dryer Combo Thermostats
- Kenmore Washer Dryer Combo Transmissions and Clutches
- Kenmore Washer Dryer Combo Valves
- Kenmore Washer Dryer Combo Wheels and Rollers
- Kenmore Washer Dryer Combo Wire Plugs and Connectors